Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1B94  Drive Motor "A" Control Module Unexpected Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU).

The cause of this malfunction may be the following:

Motor generator control ECU internal malfunction
·

Motor generator control ECU (MG ECU) malfunction



DESCRIPTION

The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU) and stores this DTC when it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A1B94 Drive Motor "A" Control Module Unexpected Operation The motor generator control ECU (MG ECU) value received by the hybrid vehicle control ECU exceeds the threshold for a certain period of time.
(1 trip detection logic)
·

Hybrid motor control inverter assembly

·

Fusible link block assembly (IGCT-MAIN)

·

IGCT relay


Comes on Master Warning: Comes on Hybrid Control A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 2 minutes or more.

HINT:

If the vehicle has returned to normal, it can be driven after turning the ignition switch to ON (READY).


4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A458544E04
0.729,3.74 1.896,3.958 1.167,0.219 10 false Auxiliary Battery 1.448,2.51 2.646,2.896 1.198,0.385 10 false Fusible Link Block Assembly 0.385,4.49 0.698,4.677 0.313,0.188 10 false PA 0.563,2.625 1.292,2.813 0.729,0.188 10 false IGCT-MAIN 5.969,3.229 6.531,3.49 0.563,0.26 10 false IGCT 5.99,3.583 6.552,3.844 0.563,0.26 10 false GND1 6.01,1.677 6.573,1.938 0.563,0.26 10 false E1 6,1.229 6.563,1.49 0.563,0.26 10 false MREL 6,0.813 6.563,1.073 0.563,0.26 10 false +B2 5.99,0.385 6.552,0.646 0.563,0.26 10 false +B1 5.344,2.375 7.115,2.563 1.771,0.188 10 false Hybrid Vehicle Control ECU 5.667,4.094 6.99,4.479 1.323,0.385 10 false Hybrid Motor Control Inverter Assembly 5.667,3.938 6.229,4.198 0.563,0.26 10 false A56 4.375,3.396 5.167,3.604 0.792,0.208 10 false IGCT NO. 2 4.458,0.948 5.104,1.146 0.646,0.198 10 false PM-IGCT 2.552,1.542 3.333,1.74 0.781,0.198 10 false IGCT 0.354,2.26 0.667,2.448 0.313,0.188 10 false O90 0.427,3.01 0.646,3.208 0.219,0.198 10 false A 5.771,0.26 6,0.448 0.229,0.188 10 false 7 5.771,0.677 5.948,0.854 0.177,0.177 10 false 8 5.729,1.094 5.948,1.271 0.219,0.177 10 false 47 5.333,2.198 5.896,2.458 0.563,0.26 10 false H44 5.74,1.521 5.969,1.708 0.229,0.188 10 false 15 5.708,3.115 5.906,3.302 0.198,0.188 10 false 12 5.719,3.448 5.948,3.635 0.229,0.188 10 false 24 4.615,3.104 4.75,3.292 0.135,0.188 10 false 1 4.865,3.104 5.021,3.302 0.156,0.198 10 false 2 4.552,0.677 4.74,0.865 0.188,0.188 10 false 1 4.813,0.677 4.99,0.865 0.177,0.188 10 false 2 2.208,0.677 2.333,0.865 0.125,0.188 10 false 3 3.01,0.698 3.146,0.865 0.135,0.167 10 false 5 3,1.094 3.156,1.26 0.156,0.167 10 false 1 2.208,1.094 2.365,1.26 0.156,0.167 10 false 2 0.208,2.25 0.365,2.417 0.156,0.167 10 false 1 0.188,3.021 0.344,3.208 0.156,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the negative (-) and positive (+) auxiliary battery terminals.

OK:

The terminals are connected securely and there is no contact problem.


HINT:

If performing a reproduction test, turn the ignition switch to ON and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

2.CHECK GROUND WIRE CONNECTION CONDITION

NG

6.CONNECT SECURELY
2.CHECK GROUND WIRE CONNECTION CONDITION
a.
A475625N02
1.01,2.406 1.24,2.583 0.229,0.177 10 true PA

Check the installation condition of the ground wires PA.

OK:

The ground wires PA are securely installed.


HINT:

If performing a reproduction test, turn the ignition switch to ON and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

3.CHECK FUSIBLE LINK BLOCK ASSEMBLY (IGCT-MAIN)

NG

7.CONNECT SECURELY
3.CHECK FUSIBLE LINK BLOCK ASSEMBLY (IGCT-MAIN)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the cable from the positive (+) auxiliary battery terminal.


c.

Check the fusible link block assembly connector O90 for improper installation.

OK:

The fusible link block assembly is installed securely and there is no contact problem.



Procedure1

a.
A458481C02
2.021,1.531 2.417,1.802 0.396,0.271 0.854,0.281 1.208,0.51 0.354,0.229 0.073,0.052 0.385,0.208 0.313,0.156 10 false *1 2.104,1.604 2.385,1.76 0.281,0.156 10 true O90 0.979,0.323 1.219,0.521 0.24,0.198 10 false A
*1 Fusible Link Block Assembly


A458566N01
1.292,0.333 1.74,0.646 0.448,0.313 1.625,1.323 1.938,1.76 true 1.406,0.417 1.729,0.615 0.323,0.198 10 false O90 1.938,1.792 2.76,2 0.823,0.208 10 false IGCT-MAIN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O90)Location & Routing

Click Connector(O90)Body>Floor Wire>Fusible Link Block Assembly

O90-1 (IGCT-MAIN) - A-1 (Positive (+) auxiliary battery terminal) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the cable from the positive (+) auxiliary battery terminal.


b.

Reconnect the cable from the negative (-) auxiliary battery terminal.



OK

4.CHECK RELAY (IGCT)

NG

8.REPAIR OR REPLACE MALFUNCTIONING PARTS
4.CHECK RELAY (IGCT)

Pre-procedure1

a.

Check the IGCT relay for improper installation.

OK:

The relay is installed securely.


HINT:

If performing a reproduction test, turn the ignition switch to ON and gently vibrate the IGCT relay with a finger before checking for DTCs.



b.
A458553C01
2.635,1.74 2.531,1.74 2.531,1.74 2.042,2.292 true 0.281,0.167 0.594,0.323 0.313,0.156 10 false *1 2.708,1.688 3.021,1.844 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT relay


Remove the IGCT relay from the No. 5 relay block assembly.


Procedure1

a.
A253297C27
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT relay.



OK

5.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

9.REPAIR OR REPLACE MALFUNCTIONING PARTS
5.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
P0A1B94 and other DTCs are output A
Only P0A1B94 is output B
None of the above conditions are met C



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

C

6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
7.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
8.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
9.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

11.SIMULATION TEST
11.SIMULATION TEST
a.

Turn the ignition switch to ON and wait for 2 minutes or more.


b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT (HYBRID CONTROL)
12.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A1B94 and other DTCs are output A
Only P0A1B94 is output B
DTCs are not output C



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

C

END