Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Shut Down Signal Circuit  


DESCRIPTION

The cause of the malfunction may be a shutdown signal.

Check whether there is a shutdown signal +B short circuit.

Related Parts Check
Area Inspection
HSDN terminal Check that the HSDN terminal voltage decreases to check for an open or short circuit while READY off (IG ON).
Hybrid vehicle control ECU, inverter, wire harness Check for open or short circuit in hybrid vehicle control ECU, inverter and wire harness.

SYSTEM DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU to the motor generator control ECU (MG ECU).

WIRING DIAGRAM

A460073E04
0.229,4.271 2.729,4.479 2.5,0.208 10 false Hybrid Motor Control Inverter Assembly 0.229,4.104 0.688,4.302 0.458,0.198 10 false A56 2,2.427 2.458,2.625 0.458,0.198 10 false +B 1.938,2.729 2.396,2.927 0.458,0.198 10 false +B2 1.802,2.969 2.26,3.167 0.458,0.198 10 false HSDN 1.823,3.563 2.281,3.76 0.458,0.198 10 false GND1 1.823,3.823 2.281,4.021 0.458,0.198 10 false GND2 2.302,2.333 2.76,2.531 0.458,0.198 10 false 6 2.292,2.635 2.75,2.833 0.458,0.198 10 false 5 2.292,3.448 2.75,3.646 0.458,0.198 10 false 24 2.292,3.719 2.75,3.917 0.458,0.198 10 false 23 2.313,2.948 2.771,3.146 0.458,0.198 10 false 22 0.469,0.792 1.344,1.167 0.875,0.375 10 false from Auxiliary Battery 4.229,0.958 4.948,1.188 0.719,0.229 10 false PM-IGCT 3.51,0.698 3.969,0.896 0.458,0.198 10 false 5 3.521,1.219 3.979,1.417 0.458,0.198 10 false 1 2.583,1.24 3.042,1.438 0.458,0.198 10 false 2 2.594,0.688 3.052,0.885 0.458,0.198 10 false 3 5.396,0.156 5.854,0.354 0.458,0.198 10 false 7 5.406,0.625 5.865,0.823 0.458,0.198 10 false 8 5.365,1.167 5.823,1.365 0.458,0.198 10 false 47 5.396,2.865 5.854,3.063 0.458,0.198 10 false 9 5.344,3.406 5.802,3.604 0.458,0.198 10 false 15 5.333,0.344 5.792,0.542 0.458,0.198 10 false H44 5.313,3.052 5.771,3.25 0.458,0.198 10 false A68 5.323,0.802 5.781,1 0.458,0.198 10 false H44 5.333,1.333 5.792,1.531 0.458,0.198 10 false H44 5.323,3.573 5.781,3.771 0.458,0.198 10 false H44 5.667,2.938 6.125,3.135 0.458,0.198 10 false HSDN 5.667,3.604 6.125,3.802 0.458,0.198 10 false E1 5.667,1.354 6.125,1.552 0.458,0.198 10 false MREL 5.677,0.844 6.135,1.042 0.458,0.198 10 false +B2 5.688,0.375 6.146,0.573 0.458,0.198 10 false +B1 1.615,0.969 2.771,1.167 1.156,0.198 10 false IGCT-MAIN 2.948,1.656 4.104,1.854 1.156,0.198 10 false IGCT 5.344,4.01 7.115,4.198 1.771,0.188 10 false Hybrid Vehicle Control ECU 2.781,2.594 4.063,2.802 1.281,0.208 10 false PCU FR

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C04
1.563,0.708 1.813,0.417 true 1.844,0.302 2.156,0.5 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A458550C18
4.688,0.219 5.104,0.469 0.417,0.25 2.427,0.208 2.844,0.458 0.417,0.25 1.896,2.229 2.438,1.25 true 5.875,2.365 5.563,1.385 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 1.594,2.281 2.135,2.479 0.542,0.198 10 false HSDN 5.896,2.406 6.208,2.563 0.313,0.156 10 false E1 2.521,0.271 3.063,0.469 0.542,0.198 10 false A68 4.792,0.281 5.333,0.479 0.542,0.198 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A68,H44)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

A68-9 (HSDN) - H44-15 (E1) Ignition switch ON Below 4.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


c.

Disconnect the A68 and H44 hybrid vehicle control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A460072C01
3,0.26 3.51,0.594 0.51,0.333 5.552,0.26 6.063,0.594 0.51,0.333 0.74,0.26 1.25,0.594 0.51,0.333 1.531,0.625 1.448,0.625 1.448,0.625 1.083,1.271 true 1.667,2.302 1.177,1.281 true 5.042,2.25 5.615,1.302 true 0.51,2.281 0.99,1.5 true 3.146,2.156 3.51,1.333 true 6.417,2.271 5.74,1.302 true 5.854,2.24 5.635,1.635 true 0.167,0.24 0.479,0.438 0.313,0.198 10 false *a 2.104,0.271 2.417,0.469 0.313,0.198 10 false *b 4.594,0.281 4.906,0.479 0.313,0.198 10 false *b 3.146,0.365 3.458,0.563 0.313,0.198 10 false A68 5.708,0.354 6.021,0.552 0.313,0.198 10 false H44 0.875,0.354 1.188,0.552 0.313,0.198 10 false A56 6.427,2.281 6.885,2.479 0.458,0.198 10 false +B2 1.635,2.313 2.094,2.51 0.458,0.198 10 false +B 5.875,2.281 6.333,2.479 0.458,0.198 10 false MREL 2.781,2.313 3.24,2.51 0.458,0.198 10 false HSDN 0.198,2.313 0.656,2.51 0.458,0.198 10 false HSDN 1.583,0.573 2.042,0.771 0.458,0.198 10 false +B2 4.865,2.281 5.323,2.479 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A56,A68)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

A56-22 (HSDN) or A68-9 (HSDN) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and hybrid motor control inverter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for 2 minutes or more.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A56,A68,H44)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

A56-22 (HSDN) - A56-6 (+B) Ignition switch off 10 kΩ or higher
A56-22 (HSDN) - A56-5 (+B2) Ignition switch off 10 kΩ or higher
A68-9 (HSDN) - H44-7 (+B1) Ignition switch off 10 kΩ or higher
A68-9 (HSDN) - H44-47 (MREL) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A68 and H44 hybrid vehicle control ECU connector.


b.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

3.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


Procedure1

a.
A365592C92
0.99,0.073 1.375,0.354 0.385,0.281 0.979,0.865 0.573,0.552 true 0.813,0.917 0.281,1.031 true 1.115,1.323 1,1.813 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.844,1.844 1.458,2.042 0.615,0.198 10 false HSDN 0.094,0.979 0.406,1.177 0.313,0.198 10 false +B 0.375,0.396 0.833,0.594 0.458,0.198 10 false +B2 1.073,0.146 1.438,0.344 0.365,0.198 10 false A56
*a Component without harness connected
(Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-22 (HSDN) - A56-6 (+B) Ignition switch off 10 kΩ or higher
A56-22 (HSDN) - A56-5 (+B2) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

NG

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY