Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P253314  Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open  


DTC SUMMARY

The hybrid vehicle control ECU stores a DTC when there is no auxiliary battery voltage to the IGR terminal even though there is auxiliary battery voltage to the IGP terminal.

DESCRIPTION

When the ignition switch is turned to ON, the auxiliary battery power source is supplied to the IGP and IGR terminals of the hybrid vehicle control ECU. When the ignition switch is off, the auxiliary battery power source is cut off.

When the ignition switch is turned off during driving, the auxiliary battery power source supplied to the IGP terminal is cut off. However, the auxiliary battery power source supplied to the IGR terminal is supplied until the vehicle is stopped*1 or until the vehicle is stopped and the ignition switch is turned off*2.

*1: w/o Entry and Start System

*2: w/ Entry and Start System

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P253314 Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open Short to ground or open in IGR terminal circuit.
(2 trip detection logic)
·

Power distribution box assembly

·

Wire harness or connector

·

Hybrid vehicle control ECU


Does not come on Master Warning: Does not come on Hybrid Control A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Turn the ignition switch ON (READY) and wait for 1 minute or more.

4.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A460289E05
0.521,6.75 2.115,7.125 1.594,0.375 10 false Auxiliary Battery 0.365,6.031 1.24,6.24 0.875,0.208 10 false BATT-MAIN 6.26,6.375 6.885,6.688 0.625,0.313 10 false E1 1.844,2.938 2.26,3.281 0.417,0.344 10 false STRG LOCK 3.24,3.042 3.865,3.354 0.625,0.313 10 false AM2 0.469,3.719 1.042,4.083 0.573,0.365 10 false INP STD NO.1-3 1.031,0.49 1.656,0.802 0.625,0.313 10 false AM1 1.74,0.49 2.365,0.802 0.625,0.313 10 false IG1 4.729,0.375 5.354,0.688 0.625,0.313 10 false IGPD 4.75,0.771 5.375,1.083 0.625,0.313 10 false +B 4.74,1.177 5.365,1.49 0.625,0.313 10 false IGRD 3.979,4.323 4.667,4.646 0.688,0.323 10 false IGR NO.1 4.698,3.688 5.375,4.094 0.677,0.406 10 false ECU IGR NO.1 6.26,3.542 6.885,3.854 0.625,0.313 10 false IGR 5.917,6.365 6.542,6.677 0.625,0.313 10 false H44 5.25,6.948 7.083,7.375 1.833,0.427 10 false Hybrid Vehicle Control ECU 5.438,3.531 6.063,3.844 0.625,0.313 10 false 4D 3.698,2.49 4.323,2.802 0.625,0.313 10 false 4B 3.083,2.49 3.708,2.802 0.625,0.313 10 false 4B 1.677,2.49 2.302,2.802 0.625,0.313 10 false 4B 1.365,3.531 1.99,3.844 0.625,0.313 10 false 4H 2.333,2.49 2.958,2.802 0.625,0.313 10 false 4C 1.438,3.333 2.063,3.646 0.625,0.313 10 false 1 1.958,2.5 2.583,2.813 0.625,0.313 10 false 4 2.594,2.5 3.219,2.813 0.625,0.313 10 false 17 3.354,2.49 3.979,2.802 0.625,0.313 10 false 9 3.979,2.49 4.604,2.802 0.625,0.313 10 false 11 5.438,3.354 6.063,3.667 0.625,0.313 10 false 22 0.958,0.917 2.188,1.281 1.229,0.365 10 false Ignition or Starter Switch Assembly*2 0.969,0.75 1.594,1.063 0.625,0.313 10 false H54 2.052,0.25 2.677,0.563 0.625,0.313 10 false 8 0.865,0.25 1.49,0.563 0.625,0.313 10 false 7 4.625,1.563 6.385,2.031 1.76,0.469 10 false Certification ECU (smart key ECU assembly)*1 2.115,7.135 5.146,7.406 3.031,0.271 10 false *1: w/ Entry and Start System 4.406,1.177 5.031,1.49 0.625,0.313 10 false H45 4.406,0.365 5.031,0.677 0.625,0.313 10 false H45 4.406,0.76 5.031,1.073 0.625,0.313 10 false H46 4.479,0.604 5.104,0.917 0.625,0.313 10 false 6 4.438,1.01 5.063,1.323 0.625,0.313 10 false 11 4.438,0.188 5.063,0.5 0.625,0.313 10 false 24 2.104,7.469 5.135,7.74 3.031,0.271 10 false *2: w/o Entry and Start System 5.958,3.323 6.583,3.635 0.625,0.313 10 false 33 5.917,3.531 6.542,3.844 0.625,0.313 10 false A68 5.948,6.167 6.573,6.479 0.625,0.313 10 false 15 2.542,5.281 4.688,5.531 2.146,0.25 10 false Power Distribution Box Assembly 5.448,4.031 6.073,4.344 0.625,0.313 10 false 36 5.448,4.469 6.073,4.781 0.625,0.313 10 false 41 5.427,4.24 6.052,4.552 0.625,0.313 10 false 4B 5.427,4.656 6.052,4.969 0.625,0.313 10 false 4C 3.448,0.479 4.073,0.792 0.625,0.313 10 false *1 3.448,0.896 4.073,1.208 0.625,0.313 10 false *1 4.021,1.344 4.646,1.656 0.625,0.313 10 false *1 2.125,0.5 2.75,0.813 0.625,0.313 10 false *2 0.344,1.49 0.969,1.802 0.625,0.313 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (IGR)
a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
IGR
50003 397 656
Standard:
GTS Display Switch Condition Specified Condition
IGR Ignition switch ON ON


Result:
Result Proceed to
The value of IGR is ON A
None of the above conditions are met B




A

B

2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

A458550C20
4.688,0.26 5.125,0.542 0.438,0.281 2.479,0.26 2.917,0.542 0.438,0.281 1.948,2.375 2.26,1.521 true 5.854,2.344 5.542,1.385 true 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 5.865,2.385 6.177,2.583 0.313,0.198 10 false E1 1.74,2.385 2.188,2.656 0.448,0.271 10 false IGR 2.594,0.333 2.927,0.583 0.333,0.25 10 false A68 4.802,0.333 5.135,0.583 0.333,0.25 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A68,H44)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

A68-33 (IGR) - H44-15 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


b.

Disconnect the 4D power distribution box assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A68)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

4D-22 - A68-33 (IGR) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A68)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

4D-22 or A68-33 (IGR) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the 4B and 4C power distribution box assembly connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-36 - Body ground Always Below 1 Ω
4C-41 - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR