Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441184 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P0A0812  DC/DC Converter Status Circuit Short to Battery  P0A0814  DC/DC Converter Status Circuit Short to Ground or Open  


DESCRIPTION

The DC/DC converter varies output voltage based on voltage change signals (VLO signal line) received from the motor generator control ECU.

If the vehicle is being driven with an inoperative DC/DC converter, the voltage of the auxiliary battery will drop, which will prevent the continued operation of the vehicle. Therefore, the motor generator control ECU monitors the operation of the DC/DC converter and alerts the driver if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A0812 DC/DC Converter Status Circuit Short to Battery Short to +B detected in DC/DC converter VLO signal line
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Motor Generator A
P0A0814 DC/DC Converter Status Circuit Short to Ground or Open
·

Open or short to ground detected in DC/DC converter VLO signal line

·

Open or short to ground detected in IGCT signal line


(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 10 seconds or more.

4.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the DTC P0A1112.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0A1112

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - IGCT RELAY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - IGCT RELAY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


c.

Remove the IGCT relay from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A459951C03
4.844,0.25 5.229,0.521 0.385,0.271 5.385,1.365 6.281,1.271 true 0.333,0.198 0.646,0.396 0.313,0.198 10 false *1 0.906,1.615 1.219,1.813 0.313,0.198 10 false *2 3.885,0.188 4.198,0.385 0.313,0.198 10 false *a 6.344,1.208 6.958,1.406 0.615,0.198 10 false IGCT 4.927,0.323 5.385,0.521 0.458,0.198 10 false A56
*1 No. 5 Relay Block Assembly *2 IGCT Relay Holder
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(A56)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

A56-12 (IGCT) - 5 (IGCT relay holder) Ignition switch off Below 1 Ω P0A0812,P0A0814


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT relay.


b.

Reconnect the A56 hybrid motor control inverter assembly connector.



OK

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR