Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441184 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P0D2D16  Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold  P0D2D17  Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold  P0D2D1F  Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Intermittent  


DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of 6 power transistors (IGBTs) each for the generator (MG1) and motor (MG2). The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for the generator (MG1) and motor (MG2); it also converts three-phase alternating current supplied by generator (MG1) and motor (MG2) into direct current for the HV battery. The motor generator control ECU (MG ECU) controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the motor generator control ECU (MG ECU).

A369835E01
1.146,0.385 1.813,0.781 0.667,0.396 10 false Generator (MG1) 3.885,0.365 4.406,0.781 0.521,0.417 10 false Motor (MG2) 3.813,1.167 3.969,1.365 0.156,0.198 10 false U 1.208,1.167 1.365,1.365 0.156,0.198 10 false U 4.104,1.167 4.26,1.365 0.156,0.198 10 false V 1.51,1.167 1.667,1.365 0.156,0.198 10 false V 1.802,1.167 1.99,1.354 0.188,0.188 10 false W 4.396,1.156 4.583,1.344 0.188,0.188 10 false W 4.26,1.698 5.469,1.958 1.208,0.26 10 false Current Sensor 1.646,1.688 2.854,1.948 1.208,0.26 10 false Current Sensor 1.313,4.25 1.625,4.448 0.313,0.198 10 false VH 3.844,4.115 5.073,4.313 1.229,0.198 10 false Inverter 0.208,6.469 1.333,6.698 1.125,0.229 10 false Boost Converter 1.823,6.813 2.135,7.01 0.313,0.198 10 false VL 1.813,7.833 2.125,8.031 0.313,0.198 10 false VB 0.156,7.49 1.042,8.156 0.885,0.667 10 false Inverter with Converter Assembly 1.573,8.531 3.104,8.729 1.531,0.198 10 false HV Battery 3.115,7.823 4.948,8.021 1.833,0.198 10 false A/C Inverter 3.063,5.896 3.979,6.094 0.917,0.198 10 false MG ECU 4.188,6.208 6.479,6.406 2.292,0.198 10 false DC/DC Converter 5.917,5.854 6.875,6.271 0.958,0.417 10 false Hybrid Vehicle Control ECU

The motor generator control ECU (MG ECU) uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage (VH) and allow control of the voltage boost.

The inverter voltage sensor outputs voltage that fluctuates between 0 to 5 V according to changes in VH.

The motor generator ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold Inverter voltage (VH) signal is stuck low:
DTC stored when the VH sensor signal is excessively low.
(1 trip detection logic)
Hybrid motor control inverter assembly Comes on Master Warning:
Comes on
Motor Generator A
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold Inverter voltage (VH) signal is stuck high:
DTC stored when the VH sensor signal is excessively high.
(1 trip detection logic)
Hybrid motor control inverter assembly Comes on Master Warning:
Comes on
Motor Generator A
P0D2D1F Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Intermittent An excessively high or low voltage signal is output from the inverter voltage sensor (VH) when DTC P0C7917, P0E5717, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
Hybrid motor control inverter assembly Does not come on Master Warning:
Does not come on
Motor Generator A

Related Data List
DTC No. Data List
P0D2D16
P0D2D17
P0D2D1F
VH Voltage

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NEXT

COMPLETED