Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441184 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P31241F  Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent  P312487  Lost Communication between Drive Motor "A" and HV ECU Missing Message  


DESCRIPTION

The motor generator control ECU, which is built into the hybrid motor control inverter assembly, controls the motor (MG2) based on commands from the hybrid vehicle control ECU.

The motor generator control ECU (MG ECU) monitors communication data and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P31241F Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard) detected when DTC P0C7917, P0E5717, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Does not come on
Motor Generator A
P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid motor control inverter assembly

·

Hybrid vehicle control ECU


Comes on Master Warning:
Comes on
Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the Inverter Low-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.CHECK DIAGNOSIS RELATED INFORMATION (P31241F)
2.CHECK DIAGNOSIS RELATED INFORMATION (P31241F)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


Procedure1

a.

Read the diagnosis related information.

Powertrain > Motor Generator > Utility
Tester Display
Diagnosis Related Information
50005 395 56
Result:
Result Proceed to
Diagnosis Related Information P31241F is output A
Diagnosis Related Information P312487 is output B
None of the above conditions are met C



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

C

8.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)
3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

Pre-procedure1

a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table.


b.

Turn the ignition switch to ON.


Procedure1

a.
A459952C02
2.344,0.438 2.688,0.667 0.344,0.229 1,0.438 1.344,0.667 0.344,0.229 2.865,1.188 2.865,1.896 true 1.656,1.188 1.833,1.917 true 1.531,1.125 1.094,1.917 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.073,0.49 1.531,0.688 0.458,0.198 10 false A68 2.406,0.49 2.865,0.688 0.458,0.198 10 false H44 1.667,1.969 2.281,2.167 0.615,0.198 10 false HMCH 0.917,1.969 1.531,2.167 0.615,0.198 10 false HMCL 2.823,1.938 3.135,2.135 0.313,0.198 10 false E1 0.229,2.99 0.688,3.188 0.458,0.198 10 false CH1 0.24,3.76 0.698,3.958 0.458,0.198 10 false CH2 2.802,3.49 3.26,3.688 0.458,0.198 10 false GND 2.813,4.063 3.271,4.26 0.458,0.198 10 false GND
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A68-13 (HMCH) - H44-15 (E1)
CH2: A68-2 (HMCL) - H44-15 (E1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON

Result:
Result Proceed to
The waveform appears as shown in the illustration A
The waveform differs from the one shown in the illustration B


HINT:
·

Perform this inspection with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A68 hybrid vehicle control ECU connector.


c.

Disconnect the A56 hybrid motor control inverter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A458810C02
0.073,3.385 0.438,3.635 0.365,0.25 0.167,1.219 0.531,1.469 0.365,0.25 1.396,1.5 0.729,2.156 true 1.51,1.5 1.792,2.167 true 0.781,3.615 0.333,4.219 true 1.021,3.479 1.479,4.24 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.125,2.479 0.438,2.677 0.313,0.198 10 false *b 0.24,1.281 0.698,1.479 0.458,0.198 10 false A56 0.135,3.448 0.594,3.646 0.458,0.198 10 false A68 1.604,2.208 2.219,2.406 0.615,0.198 10 false HMCH 0.542,2.208 1.156,2.406 0.615,0.198 10 false HMCL 1.354,4.292 1.969,4.49 0.615,0.198 10 false HMCL 0.188,4.302 0.802,4.5 0.615,0.198 10 false HMCH
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(A56,A68)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

A56-20 (HMCH) or A68-13 (HMCH) - Body ground and other terminals Ignition switch ON Below 1 V P31241F,P312487
A56-19 (HMCL) or A68-2 (HMCL) - Body ground and other terminals Ignition switch ON Below 1 V P31241F,P312487


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and hybrid motor control inverter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(A56,A68)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

A56-20 (HMCH) - A68-13 (HMCH) Ignition switch off Below 1 Ω P31241F,P312487
A56-19 (HMCL) - A68-2 (HMCL) Ignition switch off Below 1 Ω P31241F,P312487


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(A56,A68)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

A56-20 (HMCH) or A68-13 (HMCH) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31241F,P312487
A56-19 (HMCL) or A68-2 (HMCL) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31241F,P312487


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured resistance is as specified.

Check that each connector between the hybrid motor control inverter assembly and hybrid vehicle control ECU is not loose or disconnected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Reconnect the A56 hybrid motor control inverter assembly connector.


c.

Reconnect the A68 hybrid vehicle control ECU connector.



OK

7.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


Procedure1

a.
A458811C02
0.042,1 0.427,1.281 0.385,0.281 0.979,1.104 1.313,1.781 true 0.396,1.771 0.74,1.26 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.26,1.823 0.802,2.031 0.542,0.208 10 false HMCH 0.115,1.073 0.427,1.271 0.313,0.198 10 false A68 1.167,1.833 1.708,2.042 0.542,0.208 10 false HMCL
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(A68)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

A68-13 (HMCH) - A68-2 (HMCL) Ignition switch off 80 to 170 Ω P31241F,P312487


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A68 hybrid vehicle control ECU connector.



OK

NG

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

8.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P31241F or P312487 is output A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B