Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P31B300  Hybrid/EV Battery Voltage High  


DESCRIPTION

If the voltage of any HV battery cell exceeds the threshold, charging will be prohibited. If charging cannot be prohibited due to an HV battery control system malfunction, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P31B300 Hybrid/EV Battery Voltage High Charging cannot be prohibited when the voltage of any HV battery cell has exceeded the specified threshold.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

No. 1 traction battery device box assembly


Comes on Master Warning:
Comes on
HV Battery A

Related Data List
DTC No. Data List
P31B300 Hybrid/EV Battery Cell 1 to 48 Voltage

The following items can be helpful when performing repairs:

Data List
·

WIN Control Limit Power

·

Hybrid/EV Battery Current

·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery SOC

·

SMRB Control Status

·

SMRG Control Status

·

SMRP Control Status


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Drive the vehicle on urban roads for approximately 10 minutes.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
Only P31B300 is output A
P31B300 and other DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

2.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK FREEZE FRAME DATA (HV BATTERY)

B

3.CHECK FREEZE FRAME DATA (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P31B300.

Powertrain > HV Battery > DTC(P31B300) > Freeze Frame Data
Tester Display
Ready Signal
SMRG Control Status
SMRB Control Status
SMRP Control Status
Hybrid/EV Battery Current
50040 398 44,23,25,27,289 P31B300
Result:
Result Proceed to
OFF is displayed for "Ready Signal", "SMRP Control Status", "SMRB Control Status" and "SMRG Control Status" and -0.5 A or less is displayed for "Hybrid/EV Battery Current". A
Other than above B


HINT:

As the ignition switch ON state may cause the DTC to be stored, freeze frame data is used to judge the cause of the DTC output.



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK VEHICLE

B

4.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

5.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)

B

7.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)
5.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)

OK

6.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

6.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NEXT

END

7.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)

OK

8.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

8.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NEXT

END