Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441197 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY

a.

Inspect EV mode switch

i.
C401666C33
1.521,0.146 1.896,0.365 0.375,0.219 2.083,1.417 2.479,1.927 true 1.625,1.906 1.823,1.427 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 2.5,1.969 2.979,2.156 0.479,0.188 10 false E 1.531,1.958 2.052,2.135 0.521,0.177 10 false S 1.604,0.177 2.063,0.375 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H18)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

H18-6(S) - H18-5(E) EV mode switch being pushed and held Below 50 Ω
H18-6(S) - H18-5(E) EV mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly.



b.

Inspect DRIVE mode switch

i.
C401666C51
1.521,0.146 1.896,0.365 0.375,0.219 2.083,1.417 2.479,1.927 true 1.188,1.885 1.385,1.406 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 2.5,1.969 2.979,2.156 0.479,0.188 10 false E 1.01,1.958 1.531,2.135 0.521,0.177 10 false DRV 1.604,0.177 2.063,0.375 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H18)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

H18-8(DRV) - H18-5(E) DRIVE mode switch being pushed and held Below 50 Ω
H18-8(DRV) - H18-5(E) DRIVE mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly.



c.

Inspect illumination

i.
C401666C35
1.51,0.104 1.885,0.354 0.375,0.25 0.708,0.292 0.979,0.292 0.979,0.292 1.396,1.125 true 2.698,0.292 2.448,0.292 2.448,0.292 2.031,1.125 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.365,0.208 0.979,0.406 0.615,0.198 10 false ILL+ 2.75,0.198 3.365,0.396 0.615,0.198 10 false ILL- 1.573,0.156 2.031,0.354 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.

OK:
Tester Connection Specified Condition

Click Location & Routing(H18)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

Auxiliary Battery positive (+) - H18-4 (ILL+)
Auxiliary Battery negative (-) - H18-1 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly.



Hide 84970E 2.INSPECT MULTI-TERRAIN SELECT SWITCH

a.

Inspect the multi-terrain select switch:

i.
C446549C08
1.396,0.146 1.854,0.375 0.458,0.229 1.333,1.75 1.427,1.292 true 2.25,1.75 2.031,1.292 true 1.646,1.75 1.635,1.292 true 2.677,0.448 2.49,0.448 2.49,0.448 1.885,1.167 true 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 1.49,0.188 1.885,0.385 0.396,0.198 10 false H134 1.26,1.792 1.417,1.99 0.156,0.198 10 false B 2.26,1.781 2.583,2 0.323,0.219 10 false E 1.615,1.781 1.771,1.979 0.156,0.198 10 false B 2.76,0.365 3.125,0.594 0.365,0.229 10 false 2ND
*a Component without harness connected
(Multi-Terrain Select Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H134)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

H134-5(B) - H134-3(E) NORMAL mode switch being pushed and held Below 1 Ω
H134-5(B) - H134-3(E) NORMAL mode switch not pushed 10 kΩ or higher
H134-6(B) - H134-3(E) TRAIL mode switch being pushed and held Below 1 Ω
H134-6(B) - H134-3(E) TRAIL mode switch not pushed 10 kΩ or higher
H134-4(2ND) - H134-3(E) SNOW mode switch being pushed and held Below 1 Ω
H134-4(2ND) - H134-3(E) SNOW mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the multi-terrain select switch.



b.
C446549C07
1.396,0.146 1.854,0.375 0.458,0.229 1.219,1.729 1.219,1.292 true 2.208,1.729 2.208,1.292 true 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 1.49,0.188 1.885,0.385 0.396,0.198 10 false H134 1.125,1.781 1.458,1.979 0.333,0.198 10 false ILL+ 2.135,1.781 2.51,2.021 0.375,0.24 10 false ILL-
*a Component without harness connected
(Multi-Terrain Select Switch)


Inspect illumination

i.

Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the multi-terrain select switch.

OK:
Tester Connection Specified Condition

Click Location & Routing(H134)Location & Routing

Click Connector(H134)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 2 Combination Switch Assembly

Auxiliary Battery positive (+) - H134-7 (ILL+)
Auxiliary Battery negative (-) - H134-3 (ILL-)
Illuminates


If the result is not as specified, replace the multi-terrain select switch.