Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0441741 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly


Navigation System A
B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly


Navigation System A

WIRING DIAGRAM

E362443E34
5.115,3.146 6.854,3.729 1.74,0.583 10 false Radio and Display Receiver Assembly 0.583,1.26 2.625,1.677 2.042,0.417 10 false Navigation Antenna Assembly 0.417,3 4.104,3.344 3.688,0.344 10 false *: Antenna Cord Sub-assembly 0.594,1.104 1.156,1.438 0.563,0.333 10 false GS 5.115,2.948 5.677,3.281 0.563,0.333 10 false GP 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the antenna cord sub-assembly cable is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

B

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1


Procedure1

b.
E322997C20
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.74 2.344,3.323 true 1.854,1 2.271,0.583 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.604,1.229 0.917,1.427 0.313,0.198 10 false GS 0.771,3.521 1.083,3.719 0.313,0.198 10 false GP
*a Component without harness connected
(Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GS-3 - GP-1 Always Below 1 Ω
GS-3a - GP-1a Always Below 1 Ω
GS-3 or GP-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

4.INSPECT NAVIGATION ANTENNA ASSEMBLY

Pre-procedure1


Procedure1

b.
E381436C29
1.219,1.177 1.615,0.771 true 1.115,1.198 1.427,1.396 0.313,0.198 10 false 3a 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG