Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0441741 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E427274E04
1.354,0.552 1.531,0.729 0.177,0.177 10 false 9 0.875,1.458 1.49,1.656 0.615,0.198 10 false UDO+ 0.906,2.219 1.521,2.417 0.615,0.198 10 false UJSS 5.906,2.219 6.521,2.417 0.615,0.198 10 false USG1 5.906,1.458 6.521,1.656 0.615,0.198 10 false US1+ 5.906,0.656 6.521,0.854 0.615,0.198 10 false US1- 0.448,2.656 1.063,2.854 0.615,0.198 10 false H127 0.448,2.823 1.594,3.24 1.146,0.417 10 false No. 1 Stereo Jack Adapter Assembly 2.479,3.271 5.083,3.5 2.604,0.229 10 false : Data Signal (USB Communication Line) 3.552,1.76 4.188,1.979 0.635,0.219 10 false * 5.823,2.646 6.438,2.844 0.615,0.198 10 false H124 5.823,2.823 7.01,3.24 1.188,0.417 10 false Radio and Display Receiver Assembly 5.729,0.542 5.906,0.719 0.177,0.177 10 false 2 1.333,1.333 1.51,1.51 0.177,0.177 10 false 10 1.323,2.115 1.781,2.333 0.458,0.219 10 false [12] 5.75,2.115 5.927,2.292 0.177,0.177 10 false 5 5.74,1.323 5.917,1.5 0.177,0.177 10 false 3 0.906,0.656 1.521,0.854 0.615,0.198 10 false UDO- 2.146,2.833 4.75,3.063 2.604,0.229 10 false *: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the H124 radio and display receiver assembly connector.


b.

Disconnect the H127 No. 1 stereo jack adapter assembly connector.


c.
E439828C02
1.521,2.24 1.979,2.479 0.458,0.24 1.542,0.198 1.958,0.469 0.417,0.271 2.167,1.958 1.76,1.51 true 1.833,1.354 2.292,1.5 true 1.031,1.75 1.552,1.375 true 1.417,4.083 1.656,3.76 true 0.958,4.063 1.635,3.667 true 2.135,4 1.792,3.656 true 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.698,1.729 1.125,1.938 0.427,0.208 10 false US1+ 2.198,1.927 2.688,2.167 0.49,0.24 10 false USG1 2.313,1.438 2.729,1.688 0.417,0.25 10 false US1- 0.635,4.021 1.031,4.281 0.396,0.26 10 false UDO- 1.24,4.094 1.74,4.354 0.5,0.26 10 false UJSS 2.156,4 2.594,4.26 0.438,0.26 10 false UDO+ 1.604,0.26 2.042,0.469 0.438,0.208 10 false H124 1.604,2.281 2.021,2.479 0.417,0.198 10 false H127
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H124,H127)Location & Routing

Click Connector(H124)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H127)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 1 Stereo Jack Adapter Assembly

H124-2 (US1-) - H127-9 (UDO-) Always Below 1 Ω
H124-3 (US1+) - H127-10 (UDO+) Always Below 1 Ω
H124-5 (USG1) - H127-[12] (UJSS) Always Below 1 Ω
H124-2 (US1-) or H127-9 (UDO-) - Body ground Always 10 kΩ or higher
H124-3 (US1+) or H127-10 (UDO+) - Body ground Always 10 kΩ or higher
H124-5 (USG1) or H127-[12] (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR