Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0441741 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E408792E05
0.521,0.792 2.354,0.99 1.833,0.198 10 false from Auxiliary Battery 0.802,1.573 2.635,1.771 1.833,0.198 10 false from ACC Relay 0.438,2.375 2.271,2.573 1.833,0.198 10 false from IGR-NO. 2 Relay 3.458,0.958 3.979,1.156 0.521,0.198 10 false RADIO 3.375,1.75 5.208,1.948 1.833,0.198 10 false ECU-ACC 3.198,2.542 4.917,2.74 1.719,0.198 10 false ECU-IGR NO. 2 5.583,3.625 6.771,4.115 1.188,0.49 10 false Radio and Display Receiver Assembly 5.438,0.781 5.75,0.979 0.313,0.198 10 false H79 5.521,2.99 5.833,3.188 0.313,0.198 10 false 1 5.5,2.198 5.813,2.396 0.313,0.198 10 false 19 5.51,1.385 5.823,1.583 0.313,0.198 10 false 15 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1 5.438,1.573 5.75,1.771 0.313,0.198 10 false H79 5.438,3.156 5.75,3.354 0.313,0.198 10 false H79 5.427,2.365 5.74,2.563 0.313,0.198 10 false H80

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the H79 and H80 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H79)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H79-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H79,H80)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H79-4 (+B1) - H79-1 (GND1) Ignition switch off 11 to 14 V
H79-15 (ACC1) - H79-1 (GND1) Ignition switch ACC 11 to 14 V
H80-19 (IG) - H79-1 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR