Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for HV Model without Entry and Start System)
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441968 IMMOBILISER SYSTEM(for HV Model without Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for HV Model without Entry and Start System)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

The hybrid vehicle control ECU stores this DTC when a communication line between the hybrid vehicle control ECU and transponder key ECU assembly is malfunctioning or the communication ID of the hybrid vehicle control ECU and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid One of the following conditions is met:
·

Error in communication between hybrid vehicle control ECU and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between hybrid vehicle control ECU and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

Hybrid vehicle control ECU


Hybrid Control A
DTC Output Confirmation Operation:
·

Start the hybrid control system and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
hybrid control system cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

E366879E29
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.979,0.99 2.99,1.219 1.01,0.229 10 false 39 1.99,1.802 2.854,2.094 0.865,0.292 10 false 25 5.042,1.021 5.5,1.219 0.458,0.198 10 false 10 5.042,1.823 5.5,2.021 0.458,0.198 10 false 11 5.302,1.021 5.76,1.219 0.458,0.198 10 false EFII 4.948,2.802 5.406,3 0.458,0.198 10 false H74 5.302,1.823 5.76,2.021 0.458,0.198 10 false EFIO 0.406,2.844 1.396,3.042 0.99,0.198 10 false H44 0.406,3.021 2.188,3.292 1.781,0.271 10 false Hybrid Vehicle Control ECU 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or hybrid vehicle control ECU is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

2.INSPECT HYBRID VEHICLE CONTROL ECU (TERMINAL IMO)
2.INSPECT HYBRID VEHICLE CONTROL ECU (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

E438560C02
4.563,0.198 4.979,0.448 0.417,0.25 2.75,4.427 2.917,4.427 2.917,4.427 2.917,3.938 true 3.271,4.427 3.104,4.427 3.104,4.427 3.104,3.938 true 3.802,2.052 4.094,1.333 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.927,2.958 3.24,3.115 0.313,0.156 10 false *b 2.563,4.313 2.875,4.469 0.313,0.156 10 false *c 3.302,4.323 3.615,4.479 0.313,0.156 10 false *d 0.938,3.896 1.406,4.167 0.469,0.271 10 false GND 3.698,2.094 4.156,2.292 0.458,0.198 10 false IMO 4.646,0.24 5.083,0.479 0.438,0.24 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.



Measurement Condition
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-39 (IMO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

3.INSPECT HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)

B

6.INSPECT HYBRID VEHICLE CONTROL ECU (IMO TERMINAL VOLTAGE)

C

3.INSPECT HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

E438561C02
4.438,0.135 4.854,0.385 0.417,0.25 3.865,2.188 4.146,1.281 true 3.531,4.552 3.406,4.073 true 3.104,4.563 3.208,4.073 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 3.229,3.031 3.542,3.188 0.313,0.156 10 false *b 2.99,4.573 3.302,4.729 0.313,0.156 10 false *c 3.771,2.219 4.063,2.458 0.292,0.24 10 false IMI 4.531,0.188 4.969,0.427 0.438,0.24 10 false H44 3.542,4.573 3.833,4.813 0.292,0.24 10 false *d 0.875,4.031 1.292,4.24 0.417,0.208 10 false GND
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-25 (IMI) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

4.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Using a registered door control transmitter assembly, start hybrid control system.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

6.INSPECT HYBRID VEHICLE CONTROL ECU (IMO TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-39 (IMO) - Body ground Ignition switch turned to ON using registered door control transmitter assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



Post-procedure1

c.

None



A

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

B

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

Pre-procedure1

a.

Disconnect the H74 transponder key ECU assembly connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H74,H44)Location & Routing

Click Connector(H74)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key ECU Assembly

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H74-10 (EFII) - H44-39 (IMO) Always Below 1 Ω
H74-10 (EFII) or H44-25 (IMO) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR