When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B2784 | Antenna Coil Open / Short | The antenna coil in the transponder key coil is open/shorted. | ·
Wire harness or connector ·
Transponder key coil ·
Transponder key ECU assembly |
Immobiliser | A | DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | Antenna Coil Status |
If the transponder key ECU assembly is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check that the connector is properly connected to the transponder key coil.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Perform "DTC Output Confirmation Operation" procedure.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2784 is not output | A |
| B2784 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the H73 transponder key coil connector.
Procedure1
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to Transponder Key Coil) |
*b | Waveform 1 |
| *c | Waveform 2 | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(H73)Location & Routingewd_type=routing;type=c;code=H73 Click Connector(H73)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key Coilewd_type=component;type=c;code=H73;pinno=1,5 |
|||
| H73-1 (ANT1) - Body ground | Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder | 20 V/DIV., 2 s./DIV. | Pulse generation
(See waveform 1) |
| H73-5 (ANT2) - Body ground | Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder | 20 V/DIV., 2 s./DIV. | Pulse generation
(See waveform 2) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H74 transponder key ECU assembly connector.
Disconnect the H73 Transponder Key Coil connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H74,H73)Location & Routingewd_type=routing;type=c,c;code=H74,H73 Click Connector(H74)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key ECU Assemblyewd_type=component;type=c;code=H74;pinno=2,3 Click Connector(H73)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transponder Key Coilewd_type=component;type=c;code=H73;pinno=1,5 |
||
| H74-2 (ANT1) - H73-1 (ANT1) | Always | Below 1 Ω |
| H74-3 (ANT2) - H73-5 (ANT2) | Always | Below 1 Ω |
| H74-2 (ANT1) or H73-1 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| H74-3 (ANT2) or H73-5 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG