Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442039 CRANKSHAFT POSITION SENSOR A

M15A-FXE ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A460409N02
0.229,0.802 0.896,0.969 0.667,0.167 0.188,0.76 0.938,1.01 0.75,0.25 2.656,5.5 3.656,5.667 1,0.167 0.906,0.885 1.24,0.885 false 1.906,4.042 2.24,4.042 false 6.49,0.24 6.823,0.24 false 3.667,5.583 3.833,5.583 3.833,5.583 4.031,5.281 false 1.396,1.656 1.583,1.656 1.583,1.656 1.896,1.281 true 2.156,1.281 2.063,0.708 2.063,0.708 1.865,0.708 false 1.198,1.531 1.479,1.885 0.281,0.354 18 false 1 6.26,0.083 6.542,0.438 0.281,0.354 18 false 2 1.688,3.896 1.969,4.25 0.281,0.354 18 false 3 4.104,5.271 4.417,5.448 0.313,0.177 10 false x4 2.708,5.521 3.781,5.74 1.073,0.219 8 false 5.0 (51, 44 in.*lbf) 0.281,0.813 0.938,0.99 0.656,0.177 8 false 10 (102, 7) 3.292,5.073 3.604,5.25 0.313,0.177 10 false x4 4.823,5.063 5.135,5.24 0.313,0.177 10 false x9 1.698,0.646 1.979,1 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CRANK POSITION SENSOR 11401G - - -
2 INSPECT FOR ENGINE OIL LEAK - - - -
3 CENTER ENGINE UNDER COVER 51410 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401G 1.INSTALL CRANK POSITION SENSOR

a.
A458730N01
0.896,0.156 1.521,0.406 0.625,0.25 18 true i, ii, iii 4.531,0.125 5.073,0.417 0.542,0.292 18 true iv, v

i.

Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.



iii.

Check if the O-ring is twisted.


iv.

Using an 8 mm socket wrench, install the crankshaft position sensor to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the crankshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




v.

Connect the crankshaft position sensor connector.



Hide 2.INSPECT FOR ENGINE OIL LEAK

Hide 51410 3.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY