Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 2) › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442044 AIR FUEL RATIO SENSOR(for Sensor 2) A

M15A-FXE ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 2)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A479416N01
5.104,2.802 5.938,3.135 0.833,0.333 4.74,2.958 5.104,2.958 false 4.271,3.438 4.271,3.688 false 6.302,2.875 6.583,3.229 0.281,0.354 18 false 1 4.208,3.698 4.49,4.052 0.281,0.354 18 false 2 5.208,2.813 6.188,2.969 0.979,0.156 8 false 44 (449, 32) 5.167,2.958 6.427,3.208 1.26,0.25 8 false 37.7 (384, 28)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 AIR FUEL RATIO SENSOR 89467C - - -
2 WIRE HARNESS CLAMP BRACKET - - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

A479407N01
1.583,1.125 2.583,1.292 1,0.167 4.646,1.052 5.646,1.219 1,0.167 3.854,0.542 4.448,0.542 false 6.49,0.167 6.865,0.167 false 6.5,0.594 6.792,0.594 false 2.583,1.208 2.958,1.208 false 4.271,1.135 4.646,1.135 false 4.531,0.396 4.813,0.75 0.281,0.354 18 false 3 6.302,0.031 6.583,0.385 0.281,0.354 18 false 4 6.302,0.469 6.583,0.823 0.281,0.354 18 false 5 3.094,1.083 3.406,1.281 0.313,0.198 10 false x2 4.156,1.177 4.469,1.375 0.313,0.198 10 false x2 1.646,1.135 2.896,1.406 1.25,0.271 8 false 5.0 (51, 44 in.*lbf) 4.698,1.052 5.948,1.323 1.25,0.271 8 false 5.0 (51, 44 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

3 NO. 4 ENGINE UNDER COVER CENTER 51447D - - -
4 INSPECT FOR EXHAUST GAS LEAK - - - -
5 PERFORM INITIALIZATION - - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 89467C 1.INSTALL NO. 2 AIR FUEL RATIO SENSOR

a.
A458741C02
5.698,1 5.344,0.646 true 0.25,0.167 0.771,0.49 0.521,0.323 18 false ii, iii 4.354,0.156 4.583,0.438 0.229,0.281 18 true i 5.719,0.938 6,1.094 0.281,0.156 10 true SST 4.385,1.26 4.594,1.427 0.208,0.167 10 true *a
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the No. 2 air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Engage the 2 wire harness clamp.

NOTICE:

Make sure the white tube is between the wires.



iii.

Connect the No. 2 air fuel ratio sensor connector.



Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
A458742C01
2.906,0.26 3.219,0.458 0.313,0.198 10 false *a 4.292,0.26 4.604,0.458 0.313,0.198 10 false *b 0.573,0.167 1.365,0.542 0.792,0.375 18 false i, ii, iii
*a OK *b NG


i.

Install the wire harness clamp bracket to the No. 2 air fuel ratio sensor.

NOTICE:

Aline the edge of the wire harness clamp bracket and No. 2 air fuel ratio sensor as shown in the illustration.



ii.

Engage the guide to connect the wire harness to the wire harness clamp bracket.



Hide 51447D 3.INSTALL NO. 4 ENGINE UNDER COVER CENTER

Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the No. 2 air fuel ratio sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION