Home › Engine / Hybrid System › M15A-FKS (COOLING) › COOLING FAN SYSTEM
RM3700E _51 Engine / Hybrid System _093771 M15A-FKS COOLING _0442071 COOLING FAN SYSTEM J

M15A-FKS COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the cooling fan system have been removed/installed or replaced.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

e.

Check the operation of the cooling fan while operating it using the GTS.

OK:
Tester Operation Fan Operation
30 - 100% Cooling fan operates
0% Cooling fan stops



Result:
Result Proceed to
OK A
Cooling fan does not operate B
Cooling fan does not stop C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COOLING FAN MOTOR

C

10.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.INSPECT COOLING FAN MOTOR

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the A48 cooling fan ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A48-1(+B1) - A48-3(E1) Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A54 ECM connector.


b.

Disconnect the A48 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A54,A48)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A54-32(RFC) or A48-2(SI) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the A48 cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A48-3(E1) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

6.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)

6.INSPECT FAN NO. 1 RELAY

Result:
Result
OK
NG



OK

7.INSPECT HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPLACE FAN NO. 1 RELAY

7.INSPECT HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A450957C01
0.188,0.24 0.5,0.438 0.313,0.198 10 false *1 0.354,2.26 0.667,2.458 0.313,0.198 10 false *2
*1 Engine Room Relay Block
*2 FAN NO. 1 Relay


Remove the FAN NO. 1 relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY - AUXILIARY BATTERY)

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN NO. 1 RELAY)
a.

Disconnect the A48 cooling fan ECU connector.


b.

Remove the FAN NO. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A48-1(+B1) - 5 (FAN NO. 1 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A48-1 (+B) or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)
a.

Remove the FAN NO. 1 relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)

10.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A54 ECM connector.


b.

Disconnect the A48 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A54,A48)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

Click Connector(A48)Engine Compartment>Engine Room Main Wire>Cooling Fan ECU

A54-32(RFC) - A48-2(SI) Always Below 1 Ω



Result:
Result
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the z1 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(z1)Location & Routing

Click Connector(z1)Engine Compartment>other>Cooling Fan Motor , Cooling Fan ECU

z1-1(-) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG