Home › Engine / Hybrid System › M15A-FXE (COOLING) › COOLING FAN SYSTEM
RM3700E _51 Engine / Hybrid System _093772 M15A-FXE COOLING _0442080 COOLING FAN SYSTEM J

M15A-FXE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch status, refrigerant pressure, engine speed and vehicle speed, and sends a signal to the cooling fan ECU (cooling fan motor). The cooling fan ECU (cooling fan motor) steplessly control the speed of the cooling fan based on the duty cycle signal sent from the ECM. By sending signals to the cooling fan ECU (cooling fan motor) in accordance with the driving conditions and by controlling the cooling fan speed optimally with the ECM, both high cooling performance and quietness are ensured.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the cooling fan system have been removed/installed or replaced.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

e.

Check the operation of the cooling fan while operating it using the GTS.

OK:
Tester Operation Fan Operation
30 - 100% Cooling fan operates
0% Cooling fan stops



Result:
Result Proceed to
OK A
Cooling fan does not operate B
Cooling fan does not stop C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ECM)

C

8.INSPECT ECM (RFC TERMINAL)
2.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ECM)
a.

Disconnect the A45 cooling fan motor connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45,A53)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECM

A45-3 (SI) or A53-8 (RFC) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

3.INSPECT ECM (RFC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (RFC TERMINAL)
a.

Disconnect the A45 cooling fan motor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

f.

Operate the cooling fan motor (fan with motor assembly) using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-3 (SI) - Body ground Before Active Test (0%) → During Active Test (30% - 75%) Before Active Test (0%): Resistance is stable → During Active Test (30% - 75%): Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the RFC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR POWER SOURCE)

NG

4.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR POWER SOURCE)
a.

Disconnect the A45 cooling fan motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-1 (+B1) - A45-2 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR POWER SOURCE)

NG

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR POWER SOURCE)
a.

Disconnect the A45 cooling fan motor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-4 (IGS1) - A45-2 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - EFI-MAIN NO. 1 RELAY)
6.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the A45 cooling fan motor connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-4 (IGS1) - 3 (EFI-MAIN NO. 1 relay) Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A45 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-2 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT ECM (RFC TERMINAL)
a.

Disconnect the A45 cooling fan motor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

f.

Operate the cooling fan motor using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

A45-3 (SI) - Body ground Before Active Test (0%) → During Active Test (30% - 75%) Before Active Test (0%): Resistance is stable → During Active Test (30% - 75%): Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the RFC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ECM)
9.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ECM)
a.

Disconnect the A45 cooling fan motor connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45,A53)Location & Routing

Click Connector(A45)Engine Compartment>Engine Room Main Wire>Cooling Fan Motor

Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECM

A45-3 (SI) - A53-8 (RFC) Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR