Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441967 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B228231  Vehicle Speed Signal Circuit Open  B228262  Vehicle Speed Signal Compare Failure  


DESCRIPTION

DTC B228231 is stored when the vehicle speed signal sent by the skid control ECU via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B228262 is stored when a malfunction in the vehicle speed sensor is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B228231 Vehicle Speed Signal Circuit Open The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*)
·

Electronically controlled brake system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 25 km/h (16 mph) or more for 20 seconds, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.


B228262 Vehicle Speed Signal Compare Failure Vehicle speed signal malfunction is detected (excessive deceleration is detected). (1-trip detection logic*)
·

Electronically controlled brake system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 50 km/h (31 mph) or more for 10 seconds, and then drive the vehicle at a vehicle speed of less than 50 km/h (31 mph).



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B228231
·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the ignition switch cannot be turned from ON to off.


-
B228262
·

The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine will not start.


Steering lock motor operation is prohibited.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B228231
B228262
Power Source Control
·

Vehicle Running Condition (Line)

·

Power Supply Condition


Brake/EPB
·

Vehicle Speed



WIRING DIAGRAM

B592195E07
1.458,0.583 1.917,0.781 0.458,0.198 10 false SP1 1.823,0.563 2.135,0.76 0.313,0.198 10 false 18 4.771,0.49 5.042,0.677 0.271,0.188 10 false 13 5.094,0.573 5.552,0.771 0.458,0.198 10 false SPD 5.438,0.198 5.75,0.396 0.313,0.198 10 false +B 5.792,0.667 6.104,0.865 0.313,0.198 10 false IC 5.927,3.073 6.083,3.271 0.156,0.198 10 false E 0.583,4.427 2.635,4.698 2.052,0.271 10 false : CAN Communication Line 0.344,3.49 0.802,3.688 0.458,0.198 10 false A94 0.333,3.708 2.438,4.177 2.104,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 4.854,3.5 6.375,4.094 1.521,0.594 10 false Certification ECU (Smart Key ECU Assembly) 4.729,0.708 5.125,0.906 0.396,0.198 10 false H45 6.208,2.885 6.521,3.083 0.313,0.198 10 false 29 6.167,3.083 6.479,3.281 0.313,0.198 10 false H46

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Read the Data List according to the display on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
Vehicle Speed
50003 435 36
HINT:

Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the GTS.


OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))

NG

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Running Condition (Line) Vehicle being driven or stopped Stop or Running Stop: Vehicle stopped
Driving: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Running Condition (Line)
50003 454 402

Result:
Result Proceed to
The value of Vehicle Running Condition (Line) is Stop A
The value of Vehicle Running Condition (Line) is not Stop B



A

3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))

B

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Running Condition (Line) Vehicle being driven or stopped Stop or Running Stop: Vehicle stopped
Running: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Running Condition (Line)
50003 454 402

Result:
Result Proceed to
The value of Vehicle Running Condition (Line) is Running A
The value of Vehicle Running Condition (Line) is not Running B



A

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H45,A94)Location & Routing

Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H45-13 (SPD) - A94-18 (SP1) Always Below 1 Ω
H45-13 (SPD) or A94-18 (SP1) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Connect the A38 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

B574627C03
1.885,0.354 2.302,0.604 0.417,0.25 4.781,0.354 5.198,0.604 0.417,0.25 4.844,2.292 4.594,2.292 4.594,2.292 4.594,1.281 true 2.729,2.365 2.479,2.365 2.479,2.365 2.156,1.177 true 0.104,0.167 0.417,0.365 0.313,0.198 10 false *a 4.854,0.396 5.167,0.594 0.313,0.198 10 false H46 4.906,2.198 5.219,2.396 0.313,0.198 10 false E 2.792,2.281 3.198,2.479 0.406,0.198 10 false SPD 4.656,4.052 5.042,4.26 0.385,0.208 10 false GND 2.146,3.031 2.458,3.229 0.313,0.198 10 false *b 1.979,0.396 2.292,0.594 0.313,0.198 10 false H45
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H45,H46)Location & Routing

Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H45-13 (SPD) - H46-29 (E) Ignition switch ON, vehicle being driven at approx. 5 km/h (3 mph) 5 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)


HINT:

The wavelength becomes shorter as the vehicle speed increases.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)