Home › General › SPECIFICATIONS › M15A-FXE ENGINE CONTROL
RM3700E _V1 General _093022 SPECIFICATIONS _0442311 M15A-FXE ENGINE CONTROL F

SPECIFICATIONS  M15A-FXE ENGINE CONTROL  SERVICE DATA  


IGNITION SYSTEM
Standard Insulation Resistance Spark plug (terminal part) - Body ground 10 MΩ or higher
Spark Plug Type DENSO made FC16HR-Q8
NGK made DILKAR6T8
Maximum Electrode Gap for Used Spark Plug 1.2 mm (0.0472 in.)
Standard Electrode Gap for New Spark Plug 0.7 to 0.8 mm (0.0276 to 0.0315 in.)

CAMSHAFT OIL CONTROL VALVE
Standard Stroke 2.2 mm (0.0866 in.) or more

CAMSHAFT OIL CONTROL SOLENOID
Standard Resistance 1 - 2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Stroke Amount Standard 4.3 mm (0.169 in.) or more

CAMSHAFT TIMING CONTROL MOTOR
Camshaft Timing Gear Assembly Eccentric Shaft Width (A) of the Cutout Standard Width 5.98 to 6.05 mm (0.235 to 0.238 in.)
Cam Timing Control Motor with EDU Assembly Width (B) of the Joint Standard Width 5.90 to 5.95 mm (0.232 to 0.234 in.)
Joint Clearance Standard 0.03 to 0.15 mm (0.00118 to 0.00591 in.)
Maximum 0.7 mm (0.0276 in.)

THROTTLE BODY
Standard Resistance 5 (M-) - 6 (M+) 20°C (68°F) 0.3 to 100 Ω

MASS AIR FLOW METER
Standard Resistance 1 (THA) - 2 (E2G) -20°C (-4°F) 13.6 to 18.4 kΩ
20°C (68°F) 2.21 to 2.69 kΩ
60°C (140°F) 0.49 to 0.67 kΩ

ENGINE COOLANT TEMPERATURE SENSOR
Standard Resistance 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.310 to 0.326 kΩ

KNOCK SENSOR
Standard Resistance 25°C (77°F) 120 to 280 kΩ

AIR FUEL RATIO SENSOR (for Sensor 1)
Standard Resistance 4 (HA1A) - 5 (+B) 20°C (68°F) 2.5 to 3.0 Ω
1 (IP+) - 3 (VS+) Always 1 MΩ or higher

AIR FUEL RATIO SENSOR (for Sensor 2)
Standard Resistance 1 (HA1B) - 2 (+B) 20°C (68°F) 2 to 6 Ω
1 (HA1B) - 4 (A1B-) Always 10 kΩ or higher

RELAY
Standard Resistance
(No. 1 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 1))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(No. 2 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 2))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(No. 3 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 3))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(VVT Relay (VVT))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Air Fuel Ratio Sensor Heater Relay (A/F HTR))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Injector Relay (IGP))
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω