Home › Audio / Visual / Telematics › TELEMATICS › MAYDAY SWITCH
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0442574 MAYDAY SWITCH G

TELEMATICS  MAYDAY SWITCH  INSPECTION  


PROCEDURE

Hide 81260A 1.INSPECT MAYDAY SWITCH (MAP LIGHT ASSEMBLY)

a.
E436674C03
1.479,1.677 1.917,1.917 0.438,0.24 1.427,3.115 1.427,2.781 true 2.396,3.083 2.552,2.792 true 2.719,3.135 2.719,2.802 true 3.104,3.083 2.938,2.792 true 2.063,3.073 2.208,2.781 true 1.844,1.25 2.01,1.427 2.01,1.427 2.177,1.427 true 1.604,1.26 1.438,1.427 1.438,1.427 1.271,1.438 true 1.688,0.99 1.417,0.667 1.417,0.667 1.25,0.667 true 1.625,1.719 1.938,1.917 0.313,0.198 10 false V7 1.313,3.146 1.74,3.344 0.427,0.198 10 false SIG1 2.979,3.104 3.385,3.292 0.406,0.188 10 false GND3 2.625,3.146 3.031,3.333 0.406,0.188 10 false IND1 2.24,3.115 2.646,3.302 0.406,0.188 10 false IND2 1.823,3.104 2.229,3.292 0.406,0.188 10 false RRID 0.104,1.865 0.417,2.063 0.313,0.198 10 false *a 2.219,1.333 2.385,1.531 0.167,0.198 10 true *b 1.083,1.333 1.25,1.531 0.167,0.198 10 true *c 1.083,0.552 1.25,0.75 0.167,0.198 10 true *d
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
*b RED INDICATOR
*c GREEN INDICATOR
*d SOS Switch


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(V7)Location & Routing

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

V7-12(SIG1) - V7-5(GND3) Pushed 81.1 to 82.8 Ω
V7-12(SIG1) - V7-5(GND3) Not Pushed 407.8 to 416.1 Ω



ii.

If the result is not as specified, replace the mayday switch (map light assembly).



b.

Check the indicator illuminates.

i.

Apply 3 V to the connector, and check that the indicator illuminates.

HINT:

Connect 2 new dry-cell batteries (1.5 V each) in series.


OK:
Battery Connection Specified Condition
Battery positive (+) - V7-6(IND1)
Battery negative (-) - V7-5(GND3)
RED indicator illuminate
Battery positive (+) - V7-7(IND2)
Battery negative (-) - V7-5(GND3)
GREEN indicator illuminate



ii.

If the result is not as specified, replace the mayday switch (map light assembly).



c.

Check the back light illuminates.

i.

Apply 9 V to the connector, and check that the back light illuminates.

HINT:

Connect 6 new dry-cell batteries (1.5 V each) in series.


OK:
Battery Connection Specified Condition
Battery positive (+) - V7-8(RRID)
Battery negative (-) - V7-5(GND3)
Back light illuminate



ii.

If the result is not as specified, replace the mayday switch (map light assembly).