Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0442660 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


E286120E39
3.292,0.094 3.813,0.344 0.521,0.25 3.469,0.135 3.875,0.333 0.406,0.198 10 false Y2

a.

Disconnect the Y2 rear television camera assembly connector.


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
Y2-6 (CB+) - Body ground Power source Ignition switch ACC 5.5 to 7.05 V


c.

Reconnect the Y2 rear television camera assembly connector.


d.

Measure the voltage and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
Y2-3 (CV+) - Y2-2 (CV-) Video signal Ignition switch ON
Shift position in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Ignition switch ON
Shift position in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
Y2-5 (CGND) - Body ground Camera ground Always Below 1 Ω


e.
E265840C38
0.781,1.979 1.125,1.583 true 1.552,1.948 1.229,1.479 true 1.5,4.115 1.271,3.542 true 0.75,4.135 1.156,3.594 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.135 1.01,4.396 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.458,4.125 1.823,4.385 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying image)
*b Waveform 2 (camera lens covered, blacking out screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal Y2-3 (CV+) - Y2-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens not covered, displaying image

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal Y2-3 (CV+) - Y2-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens covered, blacking out screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.