Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0442660 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and radio and display receiver assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly


Rear Camera A

WIRING DIAGRAM

E378706E43
1.615,0.688 2.104,0.906 0.49,0.219 10 false CA+ 1.479,1.177 1.969,1.396 0.49,0.219 10 false CGND 1.99,0.583 2.479,0.802 0.49,0.219 10 false 30 1.99,1.052 2.479,1.271 0.49,0.219 10 false 27 5.094,1.063 5.583,1.281 0.49,0.219 10 false 5 5.094,0.583 5.583,0.802 0.49,0.219 10 false 6 4.969,1.719 5.458,1.938 0.49,0.219 10 false Y2 4.969,1.885 7.156,2.125 2.188,0.24 10 false Rear Television Camera Assembly 0.75,1.708 1.24,1.927 0.49,0.219 10 false H80 0.74,1.885 2.479,2.302 1.74,0.417 10 false Radio and Display Receiver Assembly 5.281,0.708 5.771,0.927 0.49,0.219 10 false CB+ 5.281,1.188 5.771,1.406 0.49,0.219 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:
·

When the "!" mark is displayed on the radio and display receiver assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the Y2 rear television camera assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80,Y2)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(Y2)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

H80-30 (CA+) - Y2-6 (CB+) Always Below 1 Ω
H80-27 (CGND) - Y2-5 (CGND) Always Below 1 Ω
H80-30 (CA+) or Y2-6 (CB+) - Body ground Always 10 kΩ or higher
H80-27 (CGND) or Y2-5 (CGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

Pre-procedure1

a.

Disconnect the Y2 rear television camera assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

E404546C08
5.552,1.146 6.177,1.396 0.625,0.25 3.156,0.427 3.427,0.427 3.427,0.427 3.792,1.625 true 4.198,1.625 4.469,0.344 4.469,0.344 4.708,0.344 true 5.729,1.188 6.188,1.385 0.458,0.198 10 false H80 4.802,0.281 5.396,0.49 0.594,0.208 10 false CGND 2.875,0.354 3.469,0.563 0.594,0.208 10 false CA+ 1.063,0.646 1.438,0.99 0.375,0.344 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H80-27 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H80)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H80-30 (CA+) - H80-27 (CGND) Ignition switch ACC 5.5 to 7.05 V
H80-30 (CA+) - H80-27 (CGND) Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY