The display signal from the rear television camera assembly is transmitted to the radio and display receiver assembly.
When the "!" mark is displayed on the radio and display receiver assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION
When replacing the radio and display receiver assembly, always replace it with a new one.
If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
w/ Audio and Visual System:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION
Images may be unclear even in normal conditions if:
Electrical devices are used in the cabin (noise may occur in the image).
Accessories that generate radio waves have been installed (noise may occur in the image).
The display of radio and display receiver assembly is cold (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night, etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The rear television camera assembly lens is scratched.
The rear television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the Y2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,Y2)Location & Routingewd_type=routing;type=c,c;code=H80,Y2 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=30,28,27,29,26 Click Connector(Y2)Body>No. 2 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=Y2;pinno=6,3,5,2 |
||
| H80-30 (CA+) - Y2-6 (CB+) | Always | Below 1 Ω |
| H80-28 (V+) - Y2-3 (CV+) | Always | Below 1 Ω |
| H80-27 (CGND) - Y2-5 (CGND) | Always | Below 1 Ω |
| H80-29 (V-) - Y2-2 (CV-) | Always | Below 1 Ω |
| H80-30 (CA+) or Y2-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| H80-28 (V+) or Y2-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| H80-27 (CGND) or Y2-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| H80-29 (V-) or Y2-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| H80-26 (CSLD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radio and display receiver assembly with its connectors still connected.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=29,27 |
||
| H80-29 (V-) - Body ground | Always | Below 1 Ω |
| H80-27 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=30 |
||
| H80-30 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radio and display receiver assembly with its connectors still connected.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | H80-28 (V+) - H80-27 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear television camera assembly with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
Check if the same malfunction reoccurs when the rear view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG