| *1 | Rear Hybrid Motor Control Inverter Assembly |
Since the rear hybrid motor control inverter assembly uses waterproof connectors, the voltage and waveforms cannot be inspected directly. Standard voltage readings and waveforms are indicated for reference only.
| Terminal No.
(Symbol) |
Terminal Description | Condition | Standard Condition |
|---|---|---|---|
| N38-1 (RRF) - N38-6 (RRFG) | Rear motor resolver signal | Rear motor resolver running | Pulse generation
(Waveform 1) |
| N38-4 (RSN) - N38-9 (RSNG) | Rear motor resolver signal | Rear motor resolver running | Pulse generation
(Waveform 1) |
| N38-5 (RCS) - N38-10 (RCSG) | Rear motor resolver signal | Rear motor resolver running | Pulse generation
(Waveform 1) |
| N56-2 (CARH) - N56-1 (GNR1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 2) |
| N56-3 (ILKI) - N56-1 (GNR1) | Interlock switch | Ignition switch ON, service plug grip installed correctly | 0 to 1.5 V |
| Ignition switch ON, service plug grip not installed | 11 to 14 V | ||
| N56-4 (SDNR) - N56-1 (GNR1) | MGR shutdown signal | Ignition switch ON (READY) | 0 to 1 V |
| N56-6 (+BR1) - N56-1 (GNR1) | Rear motor generator control ECU (MGR ECU) power source | Ignition switch ON | 11 to 14 V |
| N56-8 (CARL) - N56-1 (GNR1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 2) |
| N56-10 (PCNH) - N56-1 (GNR1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| N56-11 (PCNL) - N56-1 (GNR1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| N56-13 (+BR2) - N56-1 (GNR1) | Rear motor generator control ECU (MGR ECU) power source | Ignition switch ON | 11 to 14 V |
Do not measure the voltage or waveform on the sealed side of the rear hybrid motor control inverter assembly connector. Doing so may damage the connector because the connector is waterproof.
Oscilloscope waveforms
Oscilloscope waveforms shown in the illustrations are examples for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Rear motor resolver signal)
| Item | Content |
|---|---|
| Terminal | CH1: RRF - RRFG
CH2: RSN - RSNG CH3: RCS - RCSG |
| Equipment Setting | CH1: 10 V/DIV., 1 ms./DIV.
CH2: 5 V/DIV., 1 ms./DIV. CH3: 5 V/DIV., 1 ms./DIV. |
| Condition | Rear motor resolver running |
The width indicated by (A) becomes shorter as the rotor speed increases.
Waveform 2 (CAN communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: CARH - GNR1
CH2: CARL - GNR1 |
| Equipment Setting | 1 V/DIV, 50 μs/DIV |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 3 (CAN communication signal)
| Item | Content |
|---|---|
| Terminal | CH1: PCNH - GNR1
CH2: PCNL - GNR1 |
| Equipment Setting | 1 V/DIV, 50 μs/DIV |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).