Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM D

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


The rear motor generator control ECU (MGR ECU) (rear hybrid motor control inverter assembly) has a self-diagnosis system. If the rear motor generator control ECU (MGR ECU), rear motor generator system or a component is not working properly, the ECU records the conditions that relate to the fault. The ECU also provides other appropriate messages on the multi-information display, such as the HV system warning message, HV battery warning message or discharge warning message.


2 TRIP DETECTION LOGIC


Following is the description for storage of DTC using "2 trip detection logic".

When a malfunction is first detected, the malfunction is temporarily stored in the motor generator control ECU memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


The motor generator control ECU records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



AUXILIARY BATTERY VOLTAGE


Standard Voltage:
Switch Condition Specified Condition
Ignition switch ON 11 to 14 V


If voltage is below 11 V, recharge or replace the auxiliary battery.

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART






MIL (Malfunction Indicator Lamp)


a.

The MIL is illuminated when the ignition switch is first turned on ON, before the READY indicator illuminates.


b.

When the READY indicator illuminates, the MIL should turn off. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in a system.

HINT:

If the MIL is not illuminated when the ignition switch is first turned on ON, check the MIL circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>MIL Circuit




RELEVANT SYSTEMS CHECK


The inspection areas and outline of the inspection for each circuit are listed below.

A319045E43
0.094,0.073 2.76,0.302 2.667,0.229 10 false Inspection Areas of Relevant Systems 0.521,0.656 2.521,1.167 2,0.51 10 false Inverter Water Pump With Motor Assembly (Coolant Path) 1.167,1.708 2.219,1.948 1.052,0.24 10 false Cooling System 0.917,2.167 2.594,2.365 1.677,0.198 10 false Shut Down Signal Circuit 0.604,2.646 2.375,3.052 1.771,0.406 10 false Hybrid Vehicle Control ECU 1.271,3.24 2.521,3.5 1.25,0.26 10 false Shutdown Signal 0.906,4.104 2.469,4.406 1.563,0.302 10 false Communication Circuit 0.479,4.74 1.906,4.979 1.427,0.24 10 false Power Source Circuit 1,5 2.25,5.563 1.25,0.563 10 false Inverter Low-voltage Circuit 0.979,6.635 2.521,7.167 1.542,0.531 10 false HV Battery High-voltage Line Circuit 0.719,6.208 2.25,6.406 1.531,0.198 10 false HV Battery 1.271,7.625 2.156,7.813 0.885,0.188 10 false : Coolant 1.271,8.021 2.76,8.281 1.49,0.26 10 false : High Voltage Line 3.969,7.76 5.479,7.99 1.51,0.229 10 false : Inspection Areas 2.344,7.01 4.875,7.302 2.531,0.292 10 false Hybrid Motor Control Inverter Assembly 4.615,0.698 6.146,0.896 1.531,0.198 10 false Motor Resolver 4.563,1.063 6.219,1.271 1.656,0.208 10 false Motor Resolver Circuit 4.604,2.469 6.135,2.667 1.531,0.198 10 false Generator Resolver 4.417,2.844 6.25,3.104 1.833,0.26 10 false Generator Resolver Circuit 4.615,4.177 6.146,4.375 1.531,0.198 10 false Motor (MG2) 4.458,4.563 6.073,5 1.615,0.438 10 false Motor High-voltage Circuit 4.625,5.927 6.156,6.125 1.531,0.198 10 false Generator (MG1) 4.448,6.323 5.885,6.833 1.438,0.51 10 false Generator High-voltage Circuit

A378058E24
0.083,0.052 3.698,0.313 3.615,0.26 10 false Inspection Areas of Relevant Systems 0.865,0.917 2.781,1.135 1.917,0.219 10 true Rear Shut Down Signal Circuit 0.719,1.375 2,1.813 1.281,0.438 10 false Hybrid Motor Control Inverter Assembly 1.385,1.99 2.76,2.188 1.375,0.198 10 false Shutdown Signal 2.76,5.104 4.323,5.5 1.563,0.396 10 false Rear hybrid motor control inverter assembly 4.688,2.604 6.031,2.854 1.344,0.25 10 false Rear Motor (MGR) 4.542,2.958 6.51,3.177 1.969,0.219 10 true Rear Motor High-voltage Circuit 4.667,1.26 6.042,1.458 1.375,0.198 10 false Rear Motor Resolver 4.49,1.625 6.281,1.833 1.792,0.208 10 true Rear Motor Resolver Circuit 1.344,6.208 2.656,6.417 1.313,0.208 10 false : High Voltage Line 4.104,5.948 5.323,6.177 1.219,0.229 10 false : Inspection Areas 1.01,2.844 2.458,3.094 1.448,0.25 10 false Communication Circuit 0.615,3.49 1.958,3.688 1.344,0.198 10 false Power Source Circuit 1.115,3.74 2.667,4.115 1.552,0.375 10 true Rear Inverter Low-voltage Circuit 4.729,4.271 6.167,4.479 1.438,0.208 10 false Rear Cooling System 4.698,3.917 5.469,4.115 0.771,0.198 10 false Cooling fan 0.677,4.448 1.75,4.646 1.073,0.198 10 false HV Battery

Inspection Details of Relevant Systems
System to be Inspected Malfunction Possibility Inspection Content
Motor Resolver Circuit Motor resolver signal

Open or short circuit in the motor resolver, connectors or cables


Motor High-voltage Circuit Motor (MG2) output

Open or short circuit in the motor (MG2), connectors or cables


Generator Resolver Circuit Generator resolver signal

Open or short circuit in the generator resolver, connectors or cables


Generator High-voltage Circuit Generator (MG1) output

Open or short circuit in the generator (MG1), connectors or cables


Rear Motor Resolver Circuit Rear motor resolver signal

Open or short circuit in the rear motor resolver, connectors or cables


Rear Motor High-voltage Circuit Rear motor (MGR) output

Open or short circuit in the rear motor (MGR), connectors or cables


Inverter Low-voltage Circuit Power supply voltage from +B or communication between hybrid vehicle control ECU and motor generator control ECU
·

Open or short circuit in communication line between hybrid vehicle control ECU and motor generator control ECU

·

Open or short circuit in the +B or ground lines

·

Fuse is blown


Rear Inverter Low-voltage Circuit Power supply voltage from +B or communication between motor generator ECU and Rear motor generator ECU
·

Open or short circuit in communication line between motor generator ECU and Rear motor generator ECU

·

Open or short circuit in the +B or ground lines

·

Fuse is blown


HV Battery High-voltage Line Circuit High voltage power supply from HV battery

Open or short circuit in the system main relay, connectors or cables


Cooling System Temperature abnormally high
·

Grille blockage

·

Whether coolant is present

·

Whether there is a possibility that coolant was frozen when malfunction occurs

·

Cooling hose blockage

·

HV radiator fan operation


Rear Cooling System Temperature abnormally high
·

Inverter cooling fan blockage or clog

·

Inverter cooling fan operation

·

Cooling fin blockage or clog


Shutdown Signal Circuit Shutdown signal

Open or short circuit in shutdown signal communication line between hybrid vehicle control ECU and motor generator ECU


Rear Shutdown Signal Circuit Rear Shutdown Signal

Open or short circuit in shutdown signal communication line between motor generator ECU and Rear motor generator ECU




DTC PRIORITY LEVEL AND TROUBLE AREAS


·

Each DTC diagnostic procedure for the hybrid control system consists of a combination of the various relevant system (circuit) inspections.

·

When multiple DTCs are output, performing each diagnostic procedure in order of priority can lead to a more accurate diagnosis.


A403136E02
0.49,0.781 1.875,1.438 1.385,0.656 10 false Preliminary Check and Confirmation 0.177,0.167 5.073,0.365 4.896,0.198 10 false DTC Diagnostic Procedure Pattern 0.167,9.5 5.031,9.781 4.865,0.281 10 false *1: For A through V, refer to "DTC Order of Priority and Trouble Area" below. 0.5,1.375 3.865,1.573 3.365,0.198 10 false Motor Resolver Circuit 0.281,1.969 4.26,2.167 3.979,0.198 10 false Motor High-voltage Circuit 0.271,2.563 4.25,2.76 3.979,0.198 10 false Generator Resolver Circuit 0.448,3.146 1.906,3.667 1.458,0.521 10 false Generator High-voltage Circuit 0.229,4.927 4.51,5.125 4.281,0.198 10 false Inverter Low-voltage Circuit 0.385,6.094 1.917,6.583 1.531,0.49 10 false HV Battery High-voltage Line Circuit 0.865,6.677 3.01,6.875 2.146,0.198 10 false Cooling System 0.333,7.896 4,8.094 3.667,0.198 10 false Shut Down Signal Circuit 6.844,0.24 7.156,0.438 0.313,0.198 10 false *1 0.552,3.813 1.833,4.198 1.281,0.385 10 false Rear Motor Resolver Circuit 0.385,4.406 1.833,4.885 1.448,0.479 10 false Rear Motor High-voltage Circuit 0.302,5.563 1.833,6.313 1.531,0.75 10 false Rear Inverter Low-voltage Circuit 0.531,7.417 3.438,7.615 2.906,0.198 10 false Rear Cooling System 0.438,8.563 1.896,9.167 1.458,0.604 10 false Rear Shut Down Signal Circuit

Inspection Details of Relevant Systems
DTC No. Detection Item 1 2 3 4 5 Inspection Pattern
Microcomputer Malfunction Power Source Circuit Malfunction Communication System Malfunction Sensor and Actuator Circuit Malfunction System Malfunction
P06B31C Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range - ○ - - - -
P0A1C1F Drive Motor "B" Control Module Circuit Intermittent ○ - - - - -
P0A4516 Drive Motor "B" Position Sensor Circuit Voltage Below Threshold - - - - ○ F
P0A451F Drive Motor "B" Position Sensor Circuit Intermittent - - - - ○ F
P0A4521 Drive Motor "B" Position Sensor Signal Amplitude < Minimum - - - - ○ F
P0A4522 Drive Motor "B" Position Sensor Signal Amplitude > Maximum - - - - ○ F
P0A6912 Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery - - - ○ - A
P0A6914 Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Ground or Open - - - ○ - A
P0A691C Drive Motor "B" Phase V Current(High Resolution) Circuit Voltage Out of Range - - - ○ - A
P0A691F Drive Motor "B" Phase V Current(High Resolution) Circuit Intermittent - - - ○ - A
P0A6C12 Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Battery - - - ○ - A
P0A6C14 Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Ground or Open - - - ○ - A
P0A6C1C Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range - - - ○ - A
P0A6C1F Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent - - - ○ - A
P0A799E Drive Motor "B" Inverter Stuck On - - - - ○ S
P0AF211 Drive Motor Inverter Temperature Sensor "B" Circuit Short to Ground - - - ○ - -
P0AF215 Drive Motor Inverter Temperature Sensor "B" Circuit Short to Battery or Open - - - ○ - -
P0AF21F Drive Motor Inverter Temperature Sensor "B" Circuit Intermittent - - - ○ - A
P0BD111 Drive Motor Inverter Temperature Sensor "C" Circuit Circuit Short to Ground - - - ○ - -
P0BD115 Drive Motor Inverter Temperature Sensor "C" Circuit Circuit Short to Battery or Open - - - ○ - -
P0BD11F Drive Motor Inverter Temperature Sensor "C" Circuit Circuit Intermittent - - - ○ - A
P0BF512 Drive Motor "B" Phase V Current Sensor Circuit Short to Battery - - - ○ - A
P0BF514 Drive Motor "B" Phase V Current Sensor Circuit Short to Ground or Open - - - ○ - A
P0BF51F Drive Motor "B" Phase V Current Sensor Circuit Intermittent - - - ○ - A
P0BF528 Drive Motor "B" Phase V Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P0BF912 Drive Motor "B" Phase W Current Sensor Circuit Short to Battery - - - ○ - A
P0BF914 Drive Motor "B" Phase W Current Sensor Circuit Short to Ground or Open - - - ○ - A
P0BF91F Drive Motor "B" Phase W Current Sensor Circuit Intermittent - - - ○ - A
P0BF928 Drive Motor "B" Phase W Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P0C021D Drive Motor "B" System Circuit Current Out of Range - - - - ○ T
P0C1A00 Drive Motor "B" Execution Torque Performance - - - - ○ T
P0C3100 Drive Motor Inverter Temperature Sensor "C" Circuit - - - ○ - U
P0C5513 Drive Motor "B" Position Sensor Circuit "A" Circuit Open - - - ○ - N
P0C5516 Drive Motor "B" Position Sensor Circuit "A" Circuit Voltage Below Threshold - - - ○ - A
P0C5517 Drive Motor "B" Position Sensor Circuit "A" Circuit Voltage Above Threshold - - - ○ - A
P0C551F Drive Motor "B" Position Sensor Circuit "A" Circuit Intermittent - - - ○ - A
P0C5F13 Drive Motor "B" Position Sensor Circuit "B" Circuit Open - - - ○ - N
P0C5F16 Drive Motor "B" Position Sensor Circuit "B" Circuit Voltage Below Threshold - - - ○ - A
P0C5F17 Drive Motor "B" Position Sensor Circuit "B" Circuit Voltage Above Threshold - - - ○ - A
P0C5F1F Drive Motor "B" Position Sensor Circuit "B" Circuit Intermittent - - - ○ - A
P0C7A17 Drive Motor "B" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold - - - - ○ V
P0DA316 Drive Motor "B" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold - - - - ○ -
P0DA317 Drive Motor "B" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold - - - - ○ -
P0DA31F Drive Motor "B" Inverter Voltage Sensor "A" Circuit Intermittent - - - - ○ -
P1C2C1C Drive Motor "B" Control Module AD Converter Circuit Voltage Out of Range - - - - ○ -
P1C2C49 Drive Motor "B" Control Module AD Converter Circuit Internal Electronic Failure - - - - ○ -
P1C5E19 Drive Motor "B" Inverter Circuit Current Above Threshold - - - - ○ S
P1C611F Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Intermittent - ○ - - - -
P1C631F Drive Motor "B" Control Module Offset Power Circuit Intermittent - ○ - - - -
P1C661F Drive Motor "B" Control Module Circuit Intermittent ○ - - - - -
P1CAE49 Drive Motor "B" Position Sensor Internal Electronic Failure - - - - ○ N
P1CB138 Drive Motor "B" Position Sensor REF Signal Frequency Incorrect - - - - ○ N
P1CE49E Drive Motor "B" Inverter Voltage Sensor "A" Stuck On - - - - ○ A
P262C1C Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range - ○ - - - -
P310462 Drive Motor Inverter Temperature Sensor "B" Signal Compare Failure - - - - ○ A
P31491F Lost Communication between Drive Motor "A" and "B" Circuit Intermittent - - ○ - - A
P314987 Lost Communication between Drive Motor "A" and "B" Missing Message - - ○ - - A
P31E41F Drive Motor "B" Phase V Current Sensor Circuit Intermittent - - - ○ - A
P31E51F Drive Motor "B" Phase W Current Sensor Circuit Intermittent - - - ○ - A
P33C012 Drive Motor "B" Phase V Current Sensor Sub Circuit Short to Battery - - - ○ - A
P33C014 Drive Motor "B" Phase V Current Sensor Sub Circuit Short to Ground or Open - - - ○ - A
P33C01F Drive Motor "B" Phase V Current Sensor Sub Circuit Intermittent - - - ○ - A
P33C028 Drive Motor "B" Phase V Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P33C512 Drive Motor "B" Phase W Current Sensor Sub Circuit Short to Battery - - - ○ - A
P33C514 Drive Motor "B" Phase W Current Sensor Sub Circuit Short to Ground or Open - - - ○ - A
P33C51F Drive Motor "B" Phase W Current Sensor Sub Circuit Intermittent - - - ○ - A
P33C528 Drive Motor "B" Phase W Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P33D862 Drive Motor "B" Phase V Current Sensor Signal Compare Failure - - - - ○ A
P33D962 Drive Motor "B" Phase W Current Sensor Signal Compare Failure - - - - ○ A

HINT:

The "Example of Multiple DTCs being Output" below is only one example of a malfunction condition. Therefore, a determination should not be made based on this alone.

Example of Multiple DTCs being Output:
1.

The power supply of the microcomputer decreases while the vehicle is being driven.

(a)

DTCs are detected and the vehicle behavior is as follows.


Detected DTCs
-

P06B31C (Drive Motor B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range): Power source malfunction*

-

P0A4516 (Drive Motor B" Position Sensor Circuit Voltage Below Threshold): Sensor and actuator circuit malfunction*

-

P0C5516 (Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Below Threshold): Sensor and actuator circuit malfunction*

-

P1CAE49 (Drive Motor B" Position Sensor Internal Electronic Failure): Sensor and actuator circuit malfunction*

*: Check the priority level in the "DTC Order of Priority" chart above.



Vehicle Behavior

AWD stopped

System stopped


2.

The inspection order of priority is: Microcomputer circuit → power source circuit → communication circuit → sensor and actuator circuit → system circuit. Therefore, check the repair procedure for P06B31C.

3.

Follow the repair procedures and replace the rear hybrid motor control inverter assembly. Finish the repair.


It is possible to check only the specified malfunctioning parts without having to check irrelevant parts.