Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P019511  Engine Oil Temperature Sensor Circuit Short to Ground  


DESCRIPTION

A422247E01
0.115,0.094 3.01,0.521 2.896,0.427 10 false Characteristics of Oil Temperature Sensor: 0.125,0.656 0.885,0.885 0.76,0.229 10 false Voltage [V] 1.177,3.094 2.385,3.323 1.208,0.229 10 false Temperature 0.229,1.083 0.76,1.313 0.531,0.229 10 false 4.500 0.208,1.802 0.594,2.021 0.385,0.219 10 false 2.064 0.208,2.073 0.594,2.292 0.385,0.219 10 false 1.379 0.208,2.229 0.594,2.448 0.385,0.219 10 false 1.000 0.583,2.479 0.844,2.708 0.26,0.229 10 false -30 0.896,2.479 1.156,2.708 0.26,0.229 10 false -10 1.531,2.5 1.792,2.729 0.26,0.229 10 false 25 2.521,2.51 2.823,2.75 0.302,0.24 10 false 140 2.958,2.51 3.26,2.75 0.302,0.24 10 false [°C] 2.958,2.792 3.26,3.031 0.302,0.24 10 false [°F] 0.573,2.781 0.833,3.01 0.26,0.229 10 false -22 0.927,2.781 1.188,3.01 0.26,0.229 10 false 14 1.542,2.802 1.802,3.031 0.26,0.229 10 false 77 2.531,2.802 2.833,3.042 0.302,0.24 10 false 284

The engine oil temperature sensor (engine oil pressure and temperature sensor) replaces the oil temperature with electrical signals and outputs them to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P019511 Engine Oil Temperature Sensor Circuit Short to Ground The engine oil pressure and temperature sensor output voltage is below 0.535 V for 5 seconds or more (1 trip detection logic).
·

Short in engine oil temperature sensor circuit

·

Engine oil pressure and temperature sensor

·

ECM


Does not come on Engine A SAE Code: P0197

HINT:

When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Engine Oil Temperature Sensor Malfunction
P019511 -40°C (-40°F)
·

Short to ground in THEO circuit

·

Short in EPEO to THEO circuit

·

Open in VCPE circuit



If the Data List values are normal, it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the engine oil pressure and temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil pressure and temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil pressure and temperature sensor circuit is malfunctioning and stores this DTC.

Example:

If the engine oil pressure and temperature sensor output voltage is below 0.535 V for 5 seconds or more, the ECM will store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Wait 10 seconds or more [B].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019511.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A403505E91
0.167,2.854 0.625,3.052 0.458,0.198 10 false D32 0.167,3 3.188,3.26 3.021,0.26 10 false Engine Oil Pressure and Temperature Sensor 1.406,1.021 1.719,1.219 0.313,0.198 10 false VC 1.729,0.906 1.885,1.104 0.156,0.198 10 false 3 1.25,1.719 1.813,1.948 0.563,0.229 10 false TOUT 1.729,1.604 1.885,1.802 0.156,0.198 10 false 4 1.302,2.49 1.708,2.688 0.406,0.198 10 false GND 1.74,2.385 1.896,2.583 0.156,0.198 10 false 2 4.281,0.927 4.594,1.125 0.313,0.198 10 false 124 4.333,1.604 4.792,1.802 0.458,0.198 10 false 91 4.323,2.396 4.635,2.594 0.313,0.198 10 false 92 4.604,0.917 5.167,1.208 0.563,0.292 10 false VCPE 4.646,1.604 5.104,1.802 0.458,0.198 10 false THEO 4.625,2.385 5.24,2.583 0.615,0.198 10 false EPEO 5.604,0.688 6.063,0.885 0.458,0.198 10 false 5 V 5.292,3.26 5.719,3.542 0.427,0.281 10 false ECM 5.302,1.417 5.917,1.615 0.615,0.198 10 false 180 kΩ 5.292,3.094 5.719,3.375 0.427,0.281 10 false D52

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D32)Location & Routing

Click Connector(D32)Engine Compartment>Engine Wire>Oil Pressure & Temperature Sensor

D32-3 (VC) - D32-2 (GND) Ignition switch ON 4.5 to 5.5 V
D32-4 (TOUT) - D32-2 (GND) Ignition switch ON 3.0 to 5.5 V



b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D32)Location & Routing

Click Connector(D32)Engine Compartment>Engine Wire>Oil Pressure & Temperature Sensor

D32-3 (VC) - D32-4 (TOUT) Ignition Switch off 171 to 189 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE - ECM)

Pre-procedure1

a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D32,D52)Location & Routing

Click Connector(D32)Engine Compartment>Engine Wire>Oil Pressure & Temperature Sensor

Click Connector(D52)Engine Compartment>Engine Wire>ECM

D32-3 (VC) - D52-124 (VCPE) Always Below 1 Ω
D32-4 (TOUT) or D52-91 (THEO) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR