Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P107A15  Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P107A11.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P107A11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P107A15 Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Battery or Open The fuel pressure sensor output voltage is higher than 4.85 V for 3 seconds or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on Engine A SAE Code: P107D

HINT:

When this DTC is output, check the fuel pressure in the Data List. Enter the following menus: Powertrain / Engine / Data List / Low Fuel Pressure Sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Low Fuel Pressure Sensor Malfunction
P107A15 Approximately 750 kPag or higher
·

Short in VCPF to PFL circuit

·

Open in PFL circuit

·

Open in EPFL circuit



If the Data List values are normal, it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

This DTC is stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine.

10.

Idle the engine for 10 seconds or more [A].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P107A15.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(E4)Location & Routing

Click Connector(E4)Engine Compartment>No. 5 Engine Wire>Fuel Pressure Sensor

E4-1 (VC) - E4-3 (E2) Ignition switch ON 4.75 to 5.25 V
E4-2 (PFL) - E4-3 (E2) Ignition switch ON 4.4 to 5.35 V



b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E4)Location & Routing

Click Connector(E4)Engine Compartment>No. 5 Engine Wire>Fuel Pressure Sensor

E4-3 (E2) - Body ground Ignition switch off Below 1 Ω
E4-1 (VC) - E4-2 (PFL) Ignition switch off 171 to 189 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FUEL PRESSURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NG

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E4,D52)Location & Routing

Click Connector(E4)Engine Compartment>No. 5 Engine Wire>Fuel Pressure Sensor

Click Connector(D52)Engine Compartment>Engine Wire>ECM

E4-3 (E2) - D52-128 (EPFL) Always Below 1 Ω
E4-2 (PFL) - D52-129 (PFL) Always Below 1 Ω
E4-2 (PFL) or D52-129 (PFL) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR