Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR (for Rear Side)
RM3700E _58 Vehicle Interior _092991 SEAT BELT _0443755 OCCUPANT DETECTION SENSOR(for Rear Side) G

SEAT BELT  OCCUPANT DETECTION SENSOR(for Rear Side)  INSPECTION  


PROCEDURE

Hide 71503A 1.INSPECT OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

a.

for RH Side:

i.
B521163C09
1.427,0.219 1.927,0.469 0.5,0.25 1.333,1.646 1.563,1.219 true 2.042,1.615 1.802,1.188 true 0.156,0.104 0.396,0.333 0.24,0.229 10 false *a 1.542,0.26 1.875,0.469 0.333,0.208 10 false O62 2.021,1.667 2.177,1.865 0.156,0.198 10 false E 1.24,1.656 1.396,1.854 0.156,0.198 10 false +
*a Component without harness connected
(Occupant Detection Sensor (Rear Seat Cushion Pad Sub-assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the occupant detection sensor (rear seat cushion pad sub-assembly).

Click Location & Routing(O62)Location & Routing

Click Connector(O62)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor RH

O62-1(E) - O62-2(+) Occupied Below 100 Ω
O62-1(E) - O62-2(+) Not occupied 1 MΩ or higher




b.

for Center Side:

i.
B521163C10
1.427,0.219 1.927,0.469 0.5,0.25 1.344,1.688 1.573,1.219 true 1.99,1.677 1.813,1.208 true 0.156,0.104 0.396,0.333 0.24,0.229 10 false *a 1.542,0.26 1.875,0.469 0.333,0.208 10 false O63 1.979,1.698 2.135,1.896 0.156,0.198 10 false E 1.281,1.688 1.438,1.885 0.156,0.198 10 false +
*a Component without harness connected
(Occupant Detection Sensor (Rear Seat Cushion Pad Sub-assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the occupant detection sensor (rear seat cushion pad sub-assembly).

Click Location & Routing(O63)Location & Routing

Click Connector(O63)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor Center

O63-1(E) - O63-2(+) Occupied Below 100 Ω
O63-1(E) - O63-2(+) Not occupied 1 MΩ or higher




c.

for LH Side:

i.
B521163C11
1.427,0.219 1.927,0.469 0.5,0.25 1.323,1.677 1.563,1.219 true 2,1.656 1.802,1.208 true 0.156,0.104 0.396,0.333 0.24,0.229 10 false *a 1.542,0.26 1.875,0.469 0.333,0.208 10 false O61 2.021,1.698 2.177,1.896 0.156,0.198 10 false E 1.25,1.698 1.406,1.896 0.156,0.198 10 false +
*a Component without harness connected
(Occupant Detection Sensor (Rear Seat Cushion Pad Sub-assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the occupant detection sensor (rear seat cushion pad sub-assembly).

Click Location & Routing(O61)Location & Routing

Click Connector(O61)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor LH

O61-1(E) - O61-2(+) Occupied Below 100 Ω
O61-1(E) - O61-2(+) Not occupied 1 MΩ or higher