Home › Vehicle Interior › SEAT BELT › REAR SEAT INNER BELT ASSEMBLY
RM3700E _58 Vehicle Interior _092991 SEAT BELT _0443759 REAR SEAT INNER BELT ASSEMBLY G

SEAT BELT  REAR SEAT INNER BELT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 73380X 1.INSPECT REAR SEAT INNER BELT ASSEMBLY RH

a.
B276694C88
1.531,0.313 1.938,0.531 0.406,0.219 1.063,1.781 1.354,1.198 true 2.406,1.823 1.615,1.188 true 0.094,0.115 0.458,0.417 0.365,0.302 10 false *a 0.844,1.844 1.26,2.063 0.417,0.219 10 false RBR+ 2.427,1.865 2.906,2.094 0.479,0.229 10 false RBR- 1.594,0.354 2.052,0.552 0.458,0.198 10 false O19
*a Component without harness connected
(Rear Seat Inner Belt Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the rear seat inner belt assembly RH.

Click Location & Routing(O19)Location & Routing

Click Connector(O19)Body>Floor Wire>Rear Seat Inner Belt Assembly RH

O19-5(RBR+) - O19-4(RBR-) Rear seat belt RH unfastened Below 1 Ω
O19-5(RBR+) - O19-4(RBR-) Rear seat belt RH fastened 10 kΩ or higher



Hide 73480 2.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

a.

for LH Side:

i.
B276694C85
1.521,0.292 1.938,0.51 0.417,0.219 1.135,1.813 1.375,1.208 true 2,1.813 1.542,1.208 true 0.188,0.135 0.469,0.292 0.281,0.156 10 false *a 0.969,1.875 1.344,2.104 0.375,0.229 10 false LBR+ 1.885,1.865 2.26,2.094 0.375,0.229 10 false LBR- 1.594,0.323 1.969,0.552 0.375,0.229 10 false O20
*a Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the rear seat inner with center belt assembly LH.

Click Location & Routing(O20)Location & Routing

Click Connector(O20)Body>Floor Wire>Rear Seat Inner Belt with Center Assembly LH

O20-5(LBR+) - O20-4(LBR-) Rear seat belt LH unfastened Below 1 Ω
O20-5(LBR+) - O20-4(LBR-) Rear seat belt LH fastened 10 kΩ or higher




b.

for Center Side:

i.
B276694C86
1.552,0.323 1.958,0.563 0.406,0.24 2.302,1.875 1.771,1.219 true 2.698,1.74 1.969,1.167 true 0.188,0.135 0.469,0.292 0.281,0.156 10 false *a 2.26,1.927 2.698,2.135 0.438,0.208 10 false CBR+ 2.74,1.76 3.115,1.99 0.375,0.229 10 false CBR- 1.625,0.375 1.906,0.531 0.281,0.156 10 false O20
*a Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the rear seat inner with center belt assembly LH.

Click Location & Routing(O20)Location & Routing

Click Connector(O20)Body>Floor Wire>Rear Seat Inner Belt with Center Assembly LH

O20-3(CBR+) - O20-2(CBR-) Rear seat center belt unfastened Below 1 Ω
O20-3(CBR+) - O20-2(CBR-) Rear seat center belt fastened 10 kΩ or higher