84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click here
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H60,z17,z2,H72,z16,H38,z3)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=H60,z17,z2,H72,z16,H38,z3 Click Connector(H60)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H60;pinno=1,2,4,5,6,7,8,9,10,11,12,13,14 Click Connector(z17)Instrument Panel>other>No. 1 Switch Wire , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z17;pinno=4,3,2 Click Connector(z2)Instrument Panel>other>Steering Pad Switch Assembly , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z2;pinno=12,10,9,8,6,5,4,3,2,1 Click Connector(H72)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H72;pinno=3,1 Click Connector(z16)Instrument Panel>other>Steering Wheel Assembly , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z16;pinno=3,2 Click Connector(H38)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H38;pinno=1,2 Click Connector(z3)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z3;pinno=2,1 |
||
| H60-1(SDN) - z17-4(SDN) | Always | 3 Ω or less |
| H60-2(ECC) - z2-12(ECC) | Always | 3 Ω or less |
| H60-2(ECC) - z17-3(ECC) | Always | 3 Ω or less |
| H60-4(EAU) - z2-10(EAU) | Always | 3 Ω or less |
| H60-5(AU2) - z2-9(AU2) | Always | 3 Ω or less |
| H60-6(DIST) - z2-8(DIST) | Always | 3 Ω or less |
| H60-7(HO) - A(HO) | Always | 3 Ω or less |
| H60-8(SUP) - z17-2(SUP) | Always | 3 Ω or less |
| H60-9(ILL-) - z2-6(ILL-) | Always | 3 Ω or less |
| H60-10(+DP2) - z2-5(+DP2) | Always | 3 Ω or less |
| H60-11(+DP) - z2-4(+DP) | Always | 3 Ω or less |
| H60-12(AU1) - z2-3(AU1) | Always | 3 Ω or less |
| H60-13(CCS) - z2-2(CCS) | Always | 3 Ω or less |
| H60-14(ILL+2) - z2-1(ILL+2) | Always | 3 Ω or less |
| H72-3(LDA) - z16-3(LDA) | Always | 3 Ω or less |
| H72-1(LIN) - z16-2(LIN) | Always | 3 Ω or less |
| H38-1(D+) - z3-2(D+) | Always | Below 1 Ω |
| H38-2(D-) - z3-1(D-) | Always | Below 1 Ω |
If the result is not as specified, replace the spiral cable sub-assembly.