Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH › 2020.08–2021.07
RM3700E _58 Vehicle Interior _092990 SEAT _0444017 SEAT HEATER SWITCH G

SEAT  SEAT HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 84751F 1.INSPECT SEAT HEATER SWITCH (for RH Side)

B480112C03
1.458,2.5 1.958,2.75 0.5,0.25 0.729,4.177 1.167,3.802 true 1.156,4.177 1.396,3.802 true 1.604,4.177 1.604,3.813 true 2.104,4.156 2.052,3.802 true 2.573,4.156 2.292,3.802 true 0.667,2.583 0.927,2.844 0.26,0.26 10 false *a 1.594,2.563 2.052,2.76 0.458,0.198 10 false H50 0.583,4.208 1.198,4.406 0.615,0.198 10 false ILL+ 1.083,4.198 1.698,4.396 0.615,0.198 10 false IG 1.583,4.208 2.198,4.406 0.615,0.198 10 false E 2.063,4.188 2.677,4.385 0.615,0.198 10 false LO 2.5,4.188 3.115,4.385 0.615,0.198 10 false ILL-
*a Component without harness connected (Seat Heater Switch)


a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

H50-2 (LO) - H50-5 (IG) "RH" switch off Below 1 Ω
H50-2 (LO) - H50-5 (IG) "RH" switch on 10 kΩ or higher



b.

Check the indicator illuminates.

i.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H50-5 (IG)
Battery negative (-) → H50-4 (E)
"RH" switch on illuminates



c.

Check the illuminates.

i.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H50-6 (ILL+)
Battery negative (-) → H50-1 (ILL-)
Always illuminates



Hide 84751G 2.INSPECT SEAT HEATER SWITCH (for LH Side)

B480111C04
1.458,2.5 1.958,2.75 0.5,0.25 0.729,4.177 1.167,3.802 true 1.156,4.177 1.396,3.802 true 1.604,4.177 1.604,3.813 true 2.104,4.156 2.052,3.802 true 2.573,4.156 2.292,3.802 true 0.667,2.583 0.927,2.844 0.26,0.26 10 false *a 1.594,2.563 2.052,2.76 0.458,0.198 10 false H52 0.583,4.208 1.198,4.406 0.615,0.198 10 false ILL+ 1.083,4.198 1.698,4.396 0.615,0.198 10 false IG 1.583,4.208 2.198,4.406 0.615,0.198 10 false E 2.063,4.188 2.677,4.385 0.615,0.198 10 false LO 2.5,4.188 3.115,4.385 0.615,0.198 10 false ILL-
*a Component without harness connected (Seat Heater Switch)


a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Click Location & Routing(H52)Location & Routing

Click Connector(H52)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch LH

H52-2 (LO) - H52-5 (IG) "LH" switch on Below 1 Ω
H52-2 (LO) - H52-5 (IG) "LH" switch off 10 kΩ or higher



b.

Check the indicator illuminates.

i.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H52-5 (IG)
Battery negative (-) → H52-4 (E)
"LH" switch on illuminates



c.

Check the illuminates.

i.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H52-6 (ILL+)
Battery negative (-) → H52-1 (ILL-)
Always illuminates