Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0444639 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



B332383C05
0.719,0.146 1.031,0.344 0.313,0.198 10 false *a 2.479,0.146 2.792,0.344 0.313,0.198 10 false *b
*a Centering Bolt
*b Standard Bolt


PROCEDURE

Hide 67005 1.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas "A" to "J" are within the standard ranges.

B593877N01
0.615,0.208 0.771,0.406 0.156,0.198 10 false A 1.01,0.583 1.167,0.781 0.156,0.198 10 false B 2.073,0.281 2.229,0.479 0.156,0.198 10 false C 2.49,0.594 2.646,0.792 0.156,0.198 10 false D 3.771,0.885 3.927,1.083 0.156,0.198 10 false E 4.802,0.146 4.958,0.344 0.156,0.198 10 false F 5.271,0.427 5.427,0.625 0.156,0.198 10 false G 6.354,2.01 6.51,2.208 0.156,0.198 10 false H 5.563,3.99 5.708,4.188 0.146,0.198 10 false I 4.24,4.104 4.396,4.302 0.156,0.198 10 false J

Standard Clearance:
Area Measurement Area Measurement
A 7.5 to 10.5 mm (0.295 to 0.413 in.) B -0.5 to 2.5 mm (-0.019 to 0.019 in.)
C 7.5 to 10.5 mm (0.295 to 0.413 in.) D -0.5 to 2.5 mm (-0.019 to 0.019 in.)
E 2.5 to 8.5 mm (0.098 to 0.334 in.) F 7.5 to 10.5 mm (0.295 to 0.413 in.)
G -2.5 to 2.5 mm (-0.098 to 0.098 in.) H 3.0 to 8.0 mm (0.118 to 0.314 in.)
I 3.7 to 8.7 mm (0.145 to 0.342 in.) J 3.7 to 8.7 mm (0.145 to 0.342 in.)



Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 64771G 3.REMOVE SPARE WHEEL COVER (for 2WD)

Hide 58387B 4.REMOVE REAR FLOOR FINISH PLATE

Hide 67005 5.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B565055

Loosen the 4 hinge bolts on the back door and adjust the back door position.


b.

Tighten the 4 hinge bolts on the back door after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Use the same procedure for the RH side and LH side.



c.
B565056

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 58387B 6.INSTALL REAR FLOOR FINISH PLATE

Hide 64771G 7.INSTALL SPARE WHEEL COVER (for 2WD)

Hide 58410B 8.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)