Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0444635 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B360751C04
0.688,0.083 1,0.24 0.313,0.156 10 false *a 2.5,0.083 2.813,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.

·

Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67001 1.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas "A" to "N" are within the standard ranges.

B593858N01
1.792,0.24 1.948,0.438 0.156,0.198 10 false A 3.688,0.167 3.844,0.365 0.156,0.198 10 false C 3.615,0.719 3.771,0.917 0.156,0.198 10 false D 5.333,0.604 5.49,0.802 0.156,0.198 10 false E 5.063,1.333 5.219,1.531 0.156,0.198 10 false F 6.052,2.177 6.208,2.375 0.156,0.198 10 false G 4.438,4.208 4.594,4.406 0.156,0.198 10 false I 2.833,4.115 2.99,4.313 0.156,0.198 10 false K 2.302,4.292 2.458,4.49 0.156,0.198 10 false L 0.969,1.906 1.125,2.104 0.156,0.198 10 false M 0.51,2.344 0.667,2.542 0.156,0.198 10 false N 3.865,4.333 4.021,4.531 0.156,0.198 10 false J 6.448,2.479 6.604,2.677 0.156,0.198 10 false H 1.302,0.719 1.458,0.917 0.156,0.198 10 false B

Standard Clearance:
Area Measurement Area Measurement
A 3.8 to 6.2 mm (0.150 to 0.244 in.) B -1.2 to 1.2 mm (-0.047 to 0.047 in.)
C 3.5 to 6.5 mm (0.138 to 0.256 in.) D 1.1 to 4.1 mm (0.043 to 0.161 in.)
E 3.5 to 6.5 mm (0.138 to 0.256 in.) F 2.1 to 5.1 mm (0.082 to 0.200 in.)
G 3.0 to 6.0 mm (0.118 to 0.236 in.) H -1.5 to 1.5 mm (-0.05910 to 0.05910in.)
I 3.5 to 8.5 mm (0.138 to 0.334 in.) J -2.5 to 2.5 mm (-0.098 to 0.098 in.)
K 3.5 to 8.5 mm (0.138 to 0.334 in.) L -2.5 to 2.5 mm (-0.098 to 0.098 in.)
M 3.8 to 6.2 mm (0.150 to 0.244 in.) N -1.2 to 1.2 mm (-0.047 to 0.047 in.)



Hide 67001 2.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY

a.

Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

B593859

SST
09812-00010  


b.

Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the 4 hinge bolts on the door and adjust the door position.

B593860


d.

Tighten the 4 hinge bolts on the door after adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B595393

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)