DESCRIPTION
Toyota Connected Services performs ACN (Automatic Collision Notification), SOS (manual emergency calling) and SVT (Stolen Vehicle Tracking), by audio and data communications between the vehicle and call center through a cellular phone network. As shown in the illustration, when a collision is detected, the vehicle sends its location calculated based on GPS signals and the identification code of the telematics transceiver to a call center. After the necessary information has been gathered, the call center will relay this information to emergency services.
| *a | GPS Satellite | *b | Airbag Deployment |
| *c | Carrier Network | *d | Call Center |
| *e | Emergency Vehicle | *f | The illustrations shown are examples only. The illustrations may differ from the actual service. |
SYSTEM FUNCTION
ACN (Automatic Collision Notification)
When an airbag is deployed, the vehicle connects to the call center automatically and reports the vehicle location and vehicle information by data communication. The operator will connect to the vehicle and communicate with the occupant. Even if the occupant does not answer, the operator can notify emergency services.
SOS (manual emergency calling)
After pressing the manual (SOS) switch, the occupant can talk to an operator from the call center to seek assistance.
SVT (Stolen Vehicle Tracking)
After the vehicle has been reported stolen to the police, the customer can contact the call center to begin the stolen vehicle locator process. The operator locates this vehicle by GPS and provides information to the police.
FUNCTION OF MAIN COMPONENTS
| Component | Function | ||
|---|---|---|---|
| Map Light Assembly
·
Manual (SOS) Switch |
When the manual (SOS) switch is pressed, a switch signal is sent to the telematics transceiver. (When a manual emergency call is performed.) | ||
| LED Indicator Light | Green | ·
Illuminates when the system is operating normally. ·
Blinks during an emergency call. ·
Turns off when the system is malfunctioning.
|
|
| Red | ·
Illuminates when an emergency call is made while the system is still malfunctioning. ·
Turns off when the system is operating normally. ·
Illuminates when vehicle ignition switch on to indicate a DTC. ·
Illuminates when vehicle ignition switch on to indicate a specific vehicle history (RoB).
|
||
| Telephone Microphone Assembly | Sends the microphone voice signal to the telematics transceiver. | ||
| Front No. 1 Speaker Assembly LH | Outputs sound signals received from the telematics transceiver through a front No. 1 speaker assembly LH. | ||
| Front No. 2 Speaker Assembly LH | Outputs sound signals received from the telematics transceiver through a front No. 2 speaker assembly LH. | ||
| Roof Antenna Assembly | ·
Sends and receives data and voice signals used for emergency calls via a communication network. ·
Receives GPS radio signals and sends them to the telematics transceiver. |
||
| Telematics Transceiver | ·
Uses the roof antenna assembly to send and receive data and voice signals used for emergency calls via a communication network. -
When an emergency call is made: Sends the received voice signal to the front No. 1 speaker assembly LH and front No. 2 speaker assembly LH. -
When an emergency call is made: Receives the sent voice signal from the front No. 1 speaker assembly LH and front No. 2 speaker assembly LH. -
When an emergency call is made: Sends a mute signal to the radio and display receiver assembly. (The audio system is automatically muted during an emergency call.) -
When an emergency call is made: Sends vehicle location information to the service center. -
When a warning occurs, the telematics transceiver receives a warning ON signal from the combination meter assembly via CAN communication and sends it to the service center. |
||
| Mobilephone Battery | ·
When an automatic emergency call is performed and the auxiliary battery is damaged, provides power to the telematics transceiver. ·
When a manual emergency call is made, is not used as the power source. |
||
| Airbag Sensor Assembly | Sends a collision signal to the telematics transceiver. (An automatic emergency call is made.) | ||
MAYDAY ID OUTLINE
The telematics transceiver functions as the emergency call service device to perform emergency calls.
The telematics transceiver has serial numbers (IMEI, ICCID) which can be used to identify the individual device when servicing.
The IMEI is printed on the label attached to the telematics transceiver.
COMMUNICATION SYSTEM
CAN Communication Outline
The telematics system uses CAN communication between the telematics transceiver and ECUs.
DIAGNOSTIC FUNCTION OUTLINE
The telematics system has a diagnostic function (the result will be displayed on the GTS).