Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM3700E _58 Vehicle Interior _093747 DOOR LOCK _0445086 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY (w/o Power Back Door)

a.

Check the operation of the door lock motor.

B593895C01
3.938,2.281 3.74,2.031 true 3.583,2.365 3.583,2.042 true 3.135,2.25 3.406,2.01 true 3.927,0.073 4.24,0.229 0.313,0.156 10 false *a 1.281,0.083 1.594,0.24 0.313,0.156 10 false *b 3,1.583 3.313,1.74 0.313,0.156 10 false *c 4.01,2.229 4.438,2.438 0.427,0.208 10 false ACT+ 3.427,2.396 3.854,2.604 0.427,0.208 10 false ACT- 2.969,2.24 3.396,2.448 0.427,0.208 10 false D+
*a Open (Unlock) *b Close (Lock)
*c Component without harness connected
(Back Door Lock Assembly w/ Courtesy Light Switch)
- -


i.

Move the door lock to the close (lock) position.


ii.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
1(ACT+) - Auxiliary battery positive (+)
2(ACT-) - Auxiliary battery negative (-)
Back door lock motor open (unlock) operation


If the result is not as specified, replace the back door lock assembly w/ courtesy light switch.



b.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ACT-) - 3 (D+) Close 10 kΩ or higher
2 (ACT-) - 3 (D+) Open Below 1 Ω


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



Hide 69350P 2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY (w/ Power Back Door)

a.

Check the operation.

B593896C01
3.063,1.958 3.375,2.115 0.313,0.156 10 false *a 3.417,1.625 3.729,1.781 0.313,0.156 10 false *b 3.073,1.625 3.385,1.781 0.313,0.156 10 false *c 2.896,0.781 3.094,0.969 0.198,0.188 10 true *b 3.521,0.76 3.719,0.948 0.198,0.188 10 true *c
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Close Operation Direction
*c Open Operation Direction - -


i.

Apply auxiliary battery voltage and check the operation of the closer motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) - 1
Auxiliary battery negative (-) - 2
Open Operation
Auxiliary battery positive (+) - 2
Auxiliary battery negative (-) -1
Close Operation


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



b.

Check the resistance of the half latch switch.

B593897C01
3.813,0.385 3.906,0.156 false 4.24,2.271 3.76,2.156 true 3.385,2.146 2.958,2.208 true 2.906,1.677 3.219,1.833 0.313,0.156 10 false *a 2.448,0.677 2.76,0.833 0.313,0.156 10 false *b 2.99,0.167 3.302,0.323 0.313,0.156 10 false *c 3.656,0.125 3.969,0.281 0.313,0.156 10 false *d 3.938,0.24 4.25,0.396 0.313,0.156 10 false *e 3.938,0.042 4.385,0.24 0.448,0.198 10 false 13°43' 3.219,0.125 3.677,0.302 0.458,0.177 10 false 37°23' 2.479,0.396 2.927,0.594 0.448,0.198 10 false 37°26' 4.292,2.198 4.74,2.396 0.448,0.198 10 false CLS 2.813,2.135 3.125,2.292 0.313,0.156 10 false E
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position *d Full-latch Position
*e Overstroke Position - -


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - 3 (CLS) Open position Below 1 Ω
1 (E) - 3 (CLS) Half-latch position 10 kΩ or higher
1 (E) - 3 (CLS) Full-latch position 10 kΩ or higher
1 (E) - 3 (CLS) Overstroke position 10 kΩ or higher

Tester Connection Condition Specified Condition
1 (E) - 3 (CLS) Open position → Half-latch position Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



c.
B528037C02
1.948,0.51 2.125,0.156 2.125,0.156 2.313,0.156 true 1.083,2.698 1.448,2.698 true 1.24,3.24 1.385,3.24 1.385,3.24 1.5,2.938 true 0.594,0.521 1.51,0.719 0.917,0.198 10 false 37°26' 1.333,0.26 2.25,0.458 0.917,0.198 10 false 37°23' 2.354,0.063 3.271,0.26 0.917,0.198 10 false 13°43' 0.51,0.833 0.823,1.031 0.313,0.198 10 false *b 1.083,0.313 1.396,0.51 0.313,0.198 10 false *c 1.792,0.219 2.104,0.417 0.313,0.198 10 false *d 2.104,0.344 2.417,0.542 0.313,0.198 10 false *e 0.75,2.01 1.063,2.208 0.313,0.198 10 false *a 0.927,3.156 1.385,3.354 0.458,0.198 10 false CTY 0.938,2.615 1.396,2.813 0.458,0.198 10 false E
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the full latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (CTY) - 1 (E) Open position Below 1 Ω
4 (CTY) - 1 (E) Half-latch position Below 1 Ω
4 (CTY) - 1 (E) Full-latch position 10 kΩ or higher
4 (CTY) - 1 (E) Overstroke position 10 kΩ or higher

Tester Connection Condition Specified Condition
4 (CTY) - 1 (E) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



d.
B528037C03
1.979,0.51 2.135,0.177 2.135,0.177 2.365,0.177 true 1.729,2.635 1.979,2.104 1.979,2.104 2.156,2.104 true 1.104,2.698 1.469,2.698 true 0.594,0.552 1.51,0.75 0.917,0.198 10 false 37°26' 1.344,0.271 2.26,0.469 0.917,0.198 10 false 37°23' 2.438,0.104 3.01,0.313 0.573,0.208 10 false 13°43' 0.5,0.813 0.813,1.01 0.313,0.198 10 false *b 1.063,0.323 1.375,0.521 0.313,0.198 10 false *c 1.802,0.24 2.115,0.438 0.313,0.198 10 false *d 2.094,0.344 2.406,0.542 0.313,0.198 10 false *e 0.75,2.01 1.063,2.208 0.313,0.198 10 false *a 2.208,2.01 2.667,2.208 0.458,0.198 10 false FSW 0.99,2.625 1.448,2.823 0.458,0.198 10 false E
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the pawl switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW) - 1 (E) Open position 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch position 10 kΩ or higher
2 (FSW) - 1 (E) Full-latch position 10 kΩ or higher
2 (FSW) - 1 (E) Overstroke position 10 kΩ or higher

Tester Connection Condition Specified Condition
2 (FSW) - 1 (E) Open position → Half-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch position → Full-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



e.

Check the resistance of the sector switch.

B593898C01
3.76,2.302 4.083,2.5 true 3,2.271 3.385,2.167 true 2.896,1.698 3.208,1.854 0.313,0.156 10 false *a 2.906,0.25 3.219,0.406 0.313,0.156 10 false *b 4.115,2.448 4.49,2.635 0.375,0.188 10 false OPN 2.896,2.281 3.271,2.469 0.375,0.188 10 false E
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Sector Gear in Neutral Position


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (OPN) - 1 (E) Sector gear in neutral position
(Sector switch on)
Below 1 Ω
6 (OPN) - 1 (E) Sector gear not in neutral position
(Sector switch off)
10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.