Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Electric Parking Brake ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Electric Parking Brake ECU Communication Stop Mode Communication stop for "Electric Parking Brake" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

C404412E04
0.146,1.594 0.76,1.792 0.615,0.198 10 false O87 0.135,1.771 2.99,2.042 2.854,0.271 10 false No. 9 Global CAN Junction Connector 2.229,2.323 3.729,2.594 1.5,0.271 10 false from Auxiliary Battery 2.219,2.938 3.708,3.188 1.49,0.25 10 false from IGR-NO. 2 Relay 4.354,3.135 5.385,3.354 1.031,0.219 10 false ECU-IGR NO. 2 4.667,2.5 5.438,2.75 0.771,0.25 10 false EPB 5.813,2.344 6.427,2.542 0.615,0.198 10 false BEPB 5.813,2.958 6.125,3.156 0.313,0.198 10 false IG 5.802,4.25 6.417,4.448 0.615,0.198 10 false EGND 5.406,4.771 5.865,4.969 0.458,0.198 10 false A95 5.396,4.948 7.031,5.177 1.635,0.229 10 false Brake Actuator Assembly 5.813,0.615 6.427,0.813 0.615,0.198 10 false CANH 5.813,1.156 6.427,1.354 0.615,0.198 10 false CANL 5.573,2.24 5.729,2.438 0.156,0.198 10 false 9 5.51,2.854 5.823,3.052 0.313,0.198 10 false 26 5.583,4.135 5.74,4.333 0.156,0.198 10 false 2 5.521,0.51 5.833,0.708 0.313,0.198 10 false 12 5.531,1.063 5.844,1.26 0.313,0.198 10 false 11 1.656,0.521 1.844,0.75 0.188,0.229 10 false 5 1.635,1.052 1.917,1.281 0.281,0.229 10 false 16 5.802,3.594 6.417,3.792 0.615,0.198 10 false MGND 5.583,3.479 5.74,3.677 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A95 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-12 (CANH) - A95-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-1 (MGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A95-2 (EGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-9 (BEPB) - Body ground Ignition switch off 11 to 14 V
A95-26 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)