Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0444806 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  CHECK FOR INTERMITTENT PROBLEMS  


CHECK FOR INTERMITTENT PROBLEMS


HINT:

A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the GTS.


a.

Follow the directions on the GTS to display the Data List and select areas where momentary interruption should be monitored.

HINT:
·

A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).

·

If Under intermittent remains displayed for one of the items on the GTS, check for continuity between the ECU and the item for which Under intermittent is displayed.

·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.



Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open ECM communication open detection Under intermittent or Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
-
Yaw Rate Open Yaw rate sensor open detection Under intermittent or Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Deceleration Open Acceleration sensor open detection Under intermittent or Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Steering Open Steering sensor open detection Under intermittent or Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Master Cylinder Open Master cylinder pressure sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Under intermittent / Normal Under intermittent: Noise detected
Normal: Noise not detected
-
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Yaw rate sensor voltage open detection Under intermittent / Normal
Normal: Momentary interruption not detected
-
EFI Communication Invalid ECM communication invalid detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Solenoid Power Supply Open Solenoid power supply voltage status Solenoid power supply voltage status Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Motor Power Supply Open Motor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
A/C ECU Communication Open Air conditioning amplifier assembly communication open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-

b.

Select the line graph display.


c.

Using the line graph, check whether the status is "Under intermittent" or "Normal".

OK:

Normal is displayed.


HINT:

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.



d.

While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.

OK:

Normal is displayed.


HINT:
·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.

C399553E16
0.073,0.073 4.281,0.458 4.208,0.385 10 false Reference: GTS display at momentary interruption 0.208,0.875 1.823,1.292 1.615,0.417 10 false Wire Harness condition 0.948,1.927 1.792,2.26 0.844,0.333 10 false Line Graph 2.615,1.406 3.406,1.604 0.792,0.198 10 false 1 second 4.24,1.417 5.177,1.635 0.938,0.219 10 false 2 seconds 4.083,0.375 5.385,0.688 1.302,0.313 10 false 1.5 seconds 2.427,0.354 3.458,0.552 1.031,0.198 10 false 0.5 seconds 5.656,1.76 6.927,2.073 1.271,0.313 10 false Under intermittent 5.667,2.135 6.417,2.469 0.75,0.333 10 false Normal 5.625,0.708 7.104,1 1.479,0.292 10 false Momentary interruption 5.635,1.073 6.385,1.396 0.75,0.323 10 false Normal

·

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.