TERMINALS OF ECU
| *a | Component without harness connected
(Skid Control ECU [Brake Actuator Assembly]) |
- | - |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND1) | Skid control ECU (brake actuator assembly) ground |
| 2 | - (Not used) |
| 3 | - (Not used) |
| 4 (RL-) | Rear wheel speed LH (-) signal input |
| 5 (RL+) | Rear wheel speed LH (+) power supply output |
| 6 (FR-) | Front wheel speed RH (-) signal input |
| 7 (FR+) | Front wheel speed RH (+) power supply output |
| 8 | - (Not used) |
| 9 (CSW) | VSC OFF switch (combination switch assembly) |
| 10 | - (Not used) |
| 11 (STP) | Stop light switch assembly input |
| 12 | - (Not used) |
| 13 | - (Not used) |
| 14 (+BS) | Solenoid relay power supply |
| 15 | - (Not used) |
| 16 | - (Not used) |
| 17 | - (Not used) |
| 18 (SP1) | Speed signal output for speedometer |
| 19 (RR-) | Rear wheel speed RH (-) signal input |
| 20 (RR+) | Rear wheel speed RH (+) power supply output |
| 21 (FL-) | Front wheel speed LH (-) signal input |
| 22 (FL+) | Front wheel speed LH (+) power supply output |
| 23 | - (Not used) |
| 24 | - (Not used) |
| 25 | - (Not used) |
| 26 | - (Not used) |
| 27 (CANH) | CAN communication line H |
| 28 | - (Not used) |
| 29 | - (Not used) |
| 30 (GND2) | Pump motor ground |
| 31 | - (Not used) |
| 32 (STPO) | Stop light switch assembly output |
| 33 | - (Not used) |
| 34 | - (Not used) |
| 35 (BH) | Brake hold switch (electric parking brake switch assembly) input |
| 36 | - (Not used) |
| 37 (STP2) | Stop light switch assembly input |
| 38 | - (Not used) |
| 39 | - (Not used) |
| 40 | - (Not used) |
| 41 | - (Not used) |
| 42 | - (Not used) |
| 43 (CANL) | CAN communication line L |
| 44 | - (Not used) |
| 45 (IGR) | ECU power supply input |
| 46 (BM) | Motor relay power supply |
TERMINAL INSPECTION
Disconnect the A94 connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
- | - |
Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A94-1 (GND1) - Body ground | Skid control ECU (Brake actuator assembly) ground | Always | Below 1 Ω |
| A94-9 (CSW) - Body ground | VSC OFF switch (combination switch assembly) input | VSC OFF switch (combination switch assembly) pressed and held → released | Below 1 Ω → 10 kΩ or higher |
| A94-11 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off
(Brake pedal depressed → released) |
8 to 14 V → Below 1.5 V |
| A94-14 (+BS) - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A94-18 (SP1) - Body ground | Speed signal output for speedometer | Ignition switch ON | 11 to 14 V |
| A94-30 (GND2) - Body ground | Pump motor ground | Always | Below 1 Ω |
| A94-32 (STPO) - Body ground | Stop light switch assembly output | Ignition switch ON | 11 to 14 V |
| A94-35 (BH) - Body ground | Brake hold switch (electric parking brake switch assembly) input | Brake hold switch (electric parking brake switch assembly) pressed and held → released | Below 1 Ω → 10 kΩ or higher |
| A94-37 (STP2) - Body ground | Stop light switch assembly input | Brake pedal depressed → released | 8 to 14 V → Below 1.5 V |
| A94-45 (IGR) - Body ground | ECU power supply input | Ignition switch ON | 11 to 14 V |
| A94-46 (BM) - Body ground | Motor relay power supply | Always | 11 to 14 V |