Steering sensor signals are input to the skid control ECU (brake master cylinder assembly) via the CAN communication system.
When a malfunction occurs in the communication line to the steering sensor, U012687 is output.
If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
Steering sensor zero point malfunction.
Steering sensor signal malfunction.
Steering sensor installation abnormality
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C05262A | Steering Angle Sensor Module Signal Stuck In Range | When communication is normal, a steering sensor malfunction is detected. | ·
Steering sensor ·
Wire harness or connector |
Brake/EPB | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Turn the ignition switch to ON and check that no CAN communication system DTCs are output.
Turn the ignition switch to ON (READY).
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left.
Check that no speed sensor and/or yaw rate sensor DTCs are output.
| Result | Proceed to |
|---|---|
| C05262A is output | A |
| Any CAN communication system DTCs are output | B |
| Speed sensor and/or yaw rate sensor DTCs are output | C |
If a speed sensor, or the yaw rate sensor is malfunctioning, DTCs for the steering sensor may be stored even though the steering sensor is normal.
If speed sensor and yaw rate sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering sensor.
A
B
C
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the H39 steering sensor connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure3
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39)Location & Routingewd_type=routing;type=c;code=H39 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=9 |
||
| H39-9 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39)Location & Routingewd_type=routing;type=c;code=H39 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=4 |
||
| H39-4 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39)Location & Routingewd_type=routing;type=c;code=H39 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=6 |
||
| H39-6 (ESS) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG