Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

According to the display on the GTS, read the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant
speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant
speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant
speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant
speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
Vehicle stopped: 0.0 km/h (0 mph) During deceleration/ acceleration: Changes continuously
FL Wheel Acceleration FL Wheel Acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
Vehicle stopped: 0.0 km/h (0 mph) During deceleration/ acceleration: Changes continuously
RR Wheel Acceleration RR Wheel Acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
Vehicle stopped: 0.0 km/h (0 mph) During deceleration/ acceleration: Changes continuously
RL Wheel Acceleration RL Wheel Acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
Vehicle stopped: 0.0 km/h (0 mph) During deceleration/ acceleration: Changes continuously
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration/ deceleration: Changes in proportion with acceleration
Zero Point of Decele2 Memorized zero value Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Zero Point of Decele Memorized zero value Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Sensor Memorized zero point value of yaw rate sensor 1 Min.: -128°/s
Max.: 127°/s
After completing zero point calibration: 0° -
Zero Point of Yaw Rate Sensor2 Memorized zero point value of yaw rate sensor 2 Min.: -128°/s
Max.: 127°/s
After completing zero point calibration: 0° -
Steering Angle Value Steering sensor Min.: -3276.8°
Max.: 3276.7°
- During steering operation: Changes in proportion with steering wheel rotation
Zero Point of Steering Angle Memorized zero point value of steering sensor Min.: -3276.8°
Max.: 3276.7°
- -
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage downstream of the ABS motor as monitored by the skid control ECU (brake booster with master cylinder assembly)


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake booster with master cylinder assembly) to the ABS solenoid relay


Vehicle Speed Vehicle speed (estimated vehicle speed used for various controls) Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC(TRAC)/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode -
Brake Hold Control Mode Brake hold control mode Out of control mode / Pressure hold mode / Pressure release mode / EPB lock mode Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
EPB lock mode: Parking brake is engaged during brake hold control
HINT:
·

EPB stands for electric parking brake

·

If the brake pedal is not depressed for 3 minutes of more after entering pressure hold mode, the system automatically changes to EPB lock mode



FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 Mpa
- Different according to target oil pressure of each wheel
Vehicle Speed Grade Vehicle acceleration/deceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
Downhill Assist Control SW Downhill assist control switch OFF / ON OFF: Downhill assist control switch OFF
ON: Downhill assist control switch ON
-
Stop Light SW Stop light switch assembly (STP terminal input) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Parking Brake SW Parking brake status OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Brake Hold Switch Brake hold switch (electric parking brake switch assembly) (CSW2 terminal input) OFF / ON OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON
HINT:

The brake hold switch (electric parking brake switch assembly) state is determined using the voltage at terminal CSW2


Stop Light Relay Stop light control relay (Stop light switch assembly) status (STP terminal input) OFF / ON OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed
HINT:

The voltage of power supplied to the stop lights is measured at the STP terminal.


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
-
TRC(TRAC) Control TRC(TRAC) control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC(TRAC) engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC(TRAC) brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
BA Ctrl Status BA Ctrl Status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
-
Buzzer Meter buzzer OFF / ON OFF: Buzzer off
ON: Buzzer on
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

for details on Dealer Mode (Signal Check), refer to Test Mode procedure*1

·

for details on Dealer Mode (Calibration), refer to utility*2



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 35 km/h (22 mph) or more for approximately 5 seconds


Regenerative Cooperation Regenerative cooperation OFF / ON OFF: Not operating
ON: Operating
-
TRC(TRAC)/VSC OFF SW VSC OFF switch (CSW terminal input) OFF / ON OFF: VSC OFF switch OFF
ON: VSC OFF switch ON
-
Reservoir Warning SW Brake fluid level warning switch OFF / ON OFF: Reservoir level normal
ON: Reservoir level low
-
ECB Motor Relay Brake fluid level warning switch OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
ECB Motor Relay2 Motor relay 2 operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
ECB Solenoid (SGH) Switching solenoid valve (SGH) OFF / ON OFF: Solenoid off
ON: Solenoid on
ECB: Electronically Controlled Brake System
ECB Solenoid (SSA) Switching solenoid valve (SSA) OFF / ON OFF: Solenoid off
ON: Solenoid on
ECB: Electronically Controlled Brake System
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
IGP_PT1 IGP_PT1 status OFF / ON OFF: IGP_PT1 off
ON: IGP_PT1 on
-
IGP_PT2 IGP_PT2 status OFF / ON OFF: IGP_PT2 off
ON: IGP_PT2 on
-
FR Wheel Rotatory direction for front wheel RH Forward / Back - -
FL Wheel Rotatory direction for front wheel LH Forward / Back - -
RR Wheel Rotatory direction for rear wheel RH Forward / Back - -
RL Wheel Rotatory direction for rear wheel LH Forward / Back - -
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa
Max.: 24.48 MPa
0.00 to 21.60 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal Brake pedal released: 0.00 Mpa
Reaction Force Pressure Sensor Temperature Reaction force pressure sensor temperature Min.: -80°C (-112°F)
Max.: 175°C (347°F)
Current reaction force pressure sensor temperature -
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor 2 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Quantity of Brake Pedal Stroke Brake pedal stroke amount Min.: 0 mm
Max.: 255 mm
Brake pedal released: 0 mm Reading increases when brake pedal is depressed
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 21.60 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Servo Pressure Sensor Temperature Servo pressure sensor temperature Min.: -80°C (-112°F)
Max.: 175°C (347°F)
-30 to 100°C Current servo pressure sensor temperature
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Accumulator Pressure Sensor Temperature Accumulator pressure sensor temperature Min.: -80°C (-112°F)
Max.: 175°C (347°F)
Current accumulator pressure sensor temperature -
Voltage of Stroke Sensor Voltage of brake pedal stroke sensor1 Min.: -2.500 V
Max.: 2.490 V
- -
Voltage of Stroke Sensor2 Voltage of brake pedal stroke sensor2 Min.: -2.500 V
Max.: 2.490 V
- -
FR Regenerative Request FR regenerative request torque Min.: 0 Nm
Max.: 1048560 Nm
- Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
FR Regenerative Operation FR regenerative operation torque Min.: 0 Nm
Max.: 1048560 Nm
- Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
Brake Pedal Stroke Change Speed Brake pedal stroke rate of change Min.: -2560 mm/s
Max.: 2540 mm/s
Brake pedal released or depressed and held: 0 mm/s Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal
Reaction Force Oil Pressure Change Speed Reaction force pressure rate of change Min.: -30 MPa/s
Max.: 225 MPa/s
- -
Target Oil Pressure Wheel target hydraulic pressure Min.: 0.00 MPa
Max.: 20.00 Mpa
- Changes according to the target wheel cylinder hydraulic pressure
VCSK Voltage Value VCSK voltage value Min.: 0.00 MPa
Max.: 5.500 V
4.800 to 5.200 V -
SLA Solenoid Current Linear solenoid addition valve (SLA) current Min.: 0.000 A
Max.: 1.500 A
Brake pedal released: 0.000 A -
SLR Solenoid Current Linear solenoid reduction valve (SLR) current Min.: 0.000 A
Max.: 1.500 A
Brake pedal released: 0.000 A -
SGH Solenoid Current Switching solenoid valve (SGH) current Min.: 0.000 A
Max.: 3.000 A
0.000 to 1.500 A -
SSA Solenoid Current Switching solenoid valve (SSA) current Min.: 0.000 A
Max.: 3.000 A
0.000 to 1.500 A -
STPO Stop light control relay (Stop light switch assembly) status(STPO terminal output) OFF / ON OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on)
HINT:

When STPO is ON, the stop light control relay (stop light switch assembly) turns ON and the stop lights illuminate


ABS Solenoid (SRLR) Rear pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRLH) Rear pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRR) Rear pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRH) Rear pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLR) Front pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLH) Front pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRR) Front pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRH) Front pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Motor Relay Motor relay OFF / ON OFF: Motor relay off
ON: Motor relay on
-
Solenoid Relay Solenoid relay OFF / ON OFF: Solenoid relay off
ON: Solenoid relay on
-
ECB Main Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
IGP Voltage IGP voltage value 0.000 to 20.000 V - Changes in proportion to auxiliary battery voltage
IGR Voltage IGR voltage value 0.000 to 20.000 V - Changes in proportion to auxiliary battery voltage
VM1 Voltage VM1 voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
VM2 Voltage VM2 voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
BS(linear) Voltage BS voltage value (for SLA, SLR) Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
BS(ABS) Voltage BS voltage value (for SGH, SSA) Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
VCM1 Voltage VCM1 voltage value Min.: 0.000 V
Max.: 10.000 V
6.290 to 7.640 V -
VCM2 Voltage VCM2 voltage value Min.: 0.000 V
Max.: 10.000 V
6.290 to 7.640 V -



CHECK FOR INTERMITTENT PROBLEMS


HINT:

A momentary interruption (open circuit) in the connectors and/or wire harnesses between the sensors and ECUs can be detected using the Data List function of the GTS.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Follow the directions on the GTS to display the Data List and select areas where momentary interruptions should be monitored.

HINT:

A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).


Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
FL Speed Open Front speed sensor LH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
RR Speed Open Rear speed sensor RH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
RL Speed Open Rear speed sensor LH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Yaw Rate Open Yaw rate sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Deceleration Open Acceleration sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Steering Open Steering sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Air Bag ECU Communication Open Airbag sensor assembly open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Stroke Open Brake pedal stroke sensor 1 open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Stroke2 Open Brake pedal stroke sensor 2 open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Accumulator Open Accumulator pressure sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
HV Communication Open Hybrid vehicle communication open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Reaction Force Pressure Sensor Open Reaction force pressure sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Servo Pressure Sensor Open Servo pressure sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-

f.

Push the line graph button to display the line graph.


g.

Check for intermittent shorts, etc.

OK:

Normal is displayed.


HINT:

If "Under intermittent" remains displayed on the GTS, measure the resistance between the skid control ECU and the each sensor, hybrid vehicle control ECU or airbag sensor assembly.



h.

While observing the screen, gently jiggle the connectors or wire harnesses between the ECUs and sensors, or between ECUs.

OK:

Normal is displayed.


HINT:
·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.

C399553E16
0.073,0.073 4.281,0.458 4.208,0.385 10 false Reference: GTS display at momentary interruption 0.208,0.875 1.823,1.292 1.615,0.417 10 false Wire Harness condition 0.948,1.927 1.792,2.26 0.844,0.333 10 false Line Graph 2.615,1.406 3.406,1.604 0.792,0.198 10 false 1 second 4.24,1.417 5.177,1.635 0.938,0.219 10 false 2 seconds 4.083,0.375 5.385,0.688 1.302,0.313 10 false 1.5 seconds 2.427,0.354 3.458,0.552 1.031,0.198 10 false 0.5 seconds 5.656,1.76 6.927,2.073 1.271,0.313 10 false Under intermittent 5.667,2.135 6.417,2.469 0.75,0.333 10 false Normal 5.625,0.708 7.104,1 1.479,0.292 10 false Momentary interruption 5.635,1.073 6.385,1.396 0.75,0.323 10 false Normal

·

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.





DATA LIST (STEERING ANGLE SENSOR)


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Operate the GTS to read the Data List.

Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Steering Angle Signal Information Steering angle value
(Rotation to the left side is positive)
Min.: -3070.5 deg
Max.: 3070.5 deg
Turning left: 0.0 to 3070.5 deg
Turning right: -3070.5 to 0.0 deg
During steering operation: Changes in proportion with steering wheel rotation
Sensor Malfunction Factor (Current) Sensor malfunction factor (current) Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck - -
Sensor Malfunction Factor (Past) Sensor malfunction factor (past) Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck - -
Total Distance Traveled (When Sensor Malfunction occurred) Total distance traveled (when sensor malfunction occurred) Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit (When Sensor Malfunction occurred) Total distance traveled unit (when sensor malfunction occurred) km / mile - -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

According to the display on the GTS, perform the Active Test.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
EBS Relay Emergency brake signal operation Relay Start Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


This item is displayed on the GTS but is not used
ABS Solenoid Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR)
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P or N

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR or SFRH) changes to ON/OFF during Solenoid Start (Activate)
VSC Solenoid Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) Solenoid Start (Activate)
Solenoid SMF / SMR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P or N

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate)
ECB Solenoid Linear solenoid addition valve (SLR, SLA)
Switching solenoid valve (SSA, SGH)
Solenoid Start (Activate)
Solenoid SLR / SLA / SSA / SGH
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P or N

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SLR, SLA, SSA, SGH) changes to ON/OFF during Solenoid Start (Activate)
Motor Relay ABS motor relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Operating sound of motor can be heard
Solenoid Relay Solenoid Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes.
Stop Lamp Relay Stop light control relay (Stop light switch assembly) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON
ECB Main Relay Main relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


ECB: Electronically Controlled Brake System
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid Start (Activate)
Solenoid SLR
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


ECB: Electronically Controlled Brake System
ECB Solenoid (SLA) Linear solenoid addition valve (SLA) Solenoid Start (Activate)
Solenoid SLA
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


ECB: Electronically Controlled Brake System