Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _95 ADAS / AD _095278 ADVANCED DRIVER ASSISTANCE SYSTEM _0447902 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) U

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


CHECK ECM


A458815E03
1.781,0.156 2.198,0.458 0.417,0.302 5.385,0.188 5.802,0.49 0.417,0.302 1.875,0.229 2.385,0.448 0.51,0.219 11 false D51 5.479,0.26 5.99,0.479 0.51,0.219 11 false A54

HINT:

As a waterproof connector is used for the ECM, voltage, resistance and waveform inspections cannot be performed. The voltage, resistance and waveform values are provided for reference only.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A54-21 (STP) - A54-10 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A54-22 (ST1-) - A54-10 (E1) Stop light switch assembly signal
(opposite to STP terminal)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A54-27 (CCS) - A54-28 (ECCS) Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 228 to 252 Ω
+RES switch pushed 599 to 661 Ω
-SET switch pushed 1463 to 1617 Ω


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


NOTICE:
·

Turning the ignition switch to ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the millimeter wave radar sensor assembly connector.



A402620E19
3.365,0.063 3.792,0.302 0.427,0.24 3.49,0.094 3.948,0.292 0.458,0.198 10 false B8

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
B8-1 (SGND) - Body ground Ground Always Below 1 Ω
B8-8 (IGB) - B8-1 (SGND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

Turning the ignition switch ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992E26
2.073,0.833 2.458,1.042 0.385,0.208 2.167,0.833 2.479,1.031 0.313,0.198 10 false V10

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
V10-3 (LKSW) - V10-10 (GND) Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
V10-7 (IGB) - V10-10 (GND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
V10-10 (GND) - Body ground Ground Always Below 1 Ω