Use the following procedure to troubleshoot the lane tracing assist system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage.
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
11 to 14 V (Ignition switch off)
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check if the CAN communication system is functioning normally.
Refer to CAN Bus Check in CAN Communication System.
for HV Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
CAN communication system is functioning normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, Check for DTCs.
Make a note of the output DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Using the GTS, check for vehicle control history (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Make a note of the output vehicle control history (RoB).
| Result | Proceed to |
|---|---|
| Vehicle control history (RoB) is not output | A |
| Vehicle control history (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using the GTS, clear the vehicle control history (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Using the GTS, check for vehicle control history (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle control history (RoB) is not output | A |
| Vehicle control history (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Using the GTS, Clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for DTCs.
Attempt to duplicate the malfunction and check if the DTCs are output again.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B