Use the following procedure to troubleshoot the automatic high beam system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. (for Gasoline Model) | B |
| CAN communication system DTCs are output. (for HV Model) | C |
If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.
If communication to the power steering ECU assembly cannot be established through the GTS, inspect terminals CANH and CANL of the DLC3 and the power steering ECU assembly, and the IG circuit of the power steering ECU assembly.
A
B
C
Check for DTCs.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Malfunction is duplicated but DTCs arenot output | A |
| Malfunction cannot be duplicated and DTCs are not output | B |
| DTCs are output | C |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Make sure to record the output Vehicle Control History.
| Result | Proceed to |
|---|---|
| Vehicle Control History codes are not output | A |
| Vehicle Control History code X2020 and/or X204D is output | B |
| Vehicle Control History codes other than X2020 and X204D are output | C |
A
B
C
Refer to Problem Symptoms Table.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>PROBLEM SYMPTOMS TABLE
Data List / Active Test
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>DATA LIST / ACTIVE TEST
Terminals of ECU
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM SYSTEM>TERMINALS OF ECU
Inspection
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Clear Vehicle Control History
Clear the Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check Vehicle Control History
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) codes are not output | A |
| Vehicle Control History (RoB) codes are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B