Home › General › SPECIFICATIONS › K320 MULTIDRIVE / CVT › 2020.08–2021.07
RM3700E _V1 General _093022 SPECIFICATIONS _0448586 K320 MULTIDRIVE / CVT F

SPECIFICATIONS  K320 MULTIDRIVE / CVT  SERVICE DATA  


Continuously Variable Transaxle System

*1: Connect the GTS to the DLC3 when measuring the fluid pressure.

*2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed.

Engine stall speed D 2300 +/- 400 rpm
Fluid pressure (Throttle valve fully opened)*1
Engine stall speed
2300 +/- 400 rpm
D 3400 to 4200 kPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi)
R 2400 to 3200 kPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi)
Time lag N → D Less than 1.2 seconds
N → R Less than 1.5 seconds
Engine idle speed (A/C off) N 850 to 950 rpm
Shift schedule (D) (NORMAL)
Throttle valve position (100%) Fully depressed
(Before 1st up-shift)
6050 to 6900 rpm
Fully depressed
(Highest engine speed after the 1st up-shift)
6100 to 6900 rpm
Throttle valve position (Constant opening angle)*2 30 km/h (19 mph) 900 to 1350 rpm
70 km/h (43 mph) 1150 to 1650 rpm
100 km/h (62 mph) 1800 to 2300 rpm
Kick down Accelerating from 20 km/h (12 mph) 2000 rpm or more
Shift schedule (D) (PWR)
Throttle valve position (100%) Fully depressed
(Before 1st up-shift)
6050 to 6900 rpm
Fully depressed
(Highest engine speed after the 1st up-shift)
6100 to 6900 rpm
Throttle valve position (Constant opening angle)*2 30 km/h (19 mph) 1500 to 1950 rpm
70 km/h (43 mph) 2100 to 2600 rpm
100 km/h (62 mph) 2500 to 3000 rpm
Kick down Accelerating from 20 km/h (12 mph) 2000 rpm or more
Lock-up point
Lock-up ON
(Accelerator pedal opening 5%)
D 10 to 30 km/h (6 to 19 mph)
Lock-up OFF
(Accelerator pedal opening 0%)
D 5 to 20 km/h (3 to 12 mph)

Continuously Variable Transaxle Fluid

*: Using CVT (Continuously Variable Transaxle) fluid other than the above type may cause abnormal noise or vibration, or damage the CVT (Continuously Variable Transaxle) of your vehicle.

Dry fill 8.43 liters (8.9 US qts, 7.4 Imp. qts) Toyota Genuine CVT fluid FE*

Continuously Variable Transaxle Unit
Input shaft sub-assembly Standard input shaft end play 0.387 to 1.400 mm (0.0152 to 0.0551 in.)
Clearance of C-1 clutch Pack clearance (Reference) 0.45 to 0.75 mm (0.0177 to 0.0295 in.)
Forward clutch flange thickness Part number Thickness (mm (in.)) Mark
35635-12410 (35635-K0010) 3.5 (0.138) 0
35635-12420 (35635-K0020) 3.6 (0.142) 1
35635-12430 (35635-K0030) 3.7 (0.146) 2
35635-12440 (35635-K0040) 3.8 (0.150) 3
35635-12450 (35635-K0050) 3.9 (0.154) 4
35635-12460 (35635-K0060) 4.0 (0.157) 5
35635-12470 (35635-K0070) 4.1 (0.161) 6
Forward clutch return spring sub-assembly Standard free length 18.54 mm (0.730 in.)
Planetary gear assembly Standard clearance 0.16 to 0.61 mm (0.00630 to 0.0240 in.)
Clearance of No. 1 brake Pack clearance 0.54 to 1.32 mm (0.0213 to 0.0520 in.)
1st and reverse brake return spring sub-assembly Standard free length 15.70 mm (0.618 in.)
Thrust needle roller bearing and thrust bearing race diameter Mark Thrust bearing race diameter inside / outside
mm (in.)
Thrust bearing race diameter inside / outside
mm (in.)
A - 47.75 (1.88) / 65.8 (2.59)
B 26.38 (1.04) / 38.9 (1.53) 24.9 (0.98) / 38.9 (1.53)
C - 29.7 (1.17) / 49.1 (1.93)
Straight pin Protrusion height 7.0 to 8.0 mm (0.276 to 0.315 in.)
Differential case tapered roller bearing preload (at 10 rpm) Standard turning torque 1.61 to 2.57 N*m (17 to 26 kgf*cm, 15 to 22 in.*lbf)
Shim thickness Part number Thickness (mm (in.))
90564-58002 1.76 (0.0693)
90564-58003 1.79 (0.0705)
90564-58004 1.82 (0.0717)
90564-58005 1.85 (0.0728)
90564-58006 1.88 (0.0740)
90564-58007 1.91 (0.0752)
90564-58008 1.94 (0.0764)
90564-58009 1.97 (0.0776)
90564-58010 2.00 (0.0787)
90564-58011 2.03 (0.0799)
90564-58012 2.06 (0.0811)
90564-58013 2.09 (0.0823)
90564-58014 2.12 (0.0835)
90564-58015 2.15 (0.0846)
90564-58016 2.18 (0.0858)
90564-58017 2.21 (0.0870)
90564-58018 2.24 (0.0882)
90564-58019 2.27 (0.0894)
90564-58020 2.30 (0.0906)
90564-58021 2.33 (0.0917)
Adjust reduction driven gear tapered roller bearing preload (at 10 rpm) Standard turning torque Differential case tapered roller bearing preload + 2.63 to 4.88 N*m (27 to 49 kgf*cm, 2 to 3 ft.*lbf)
Shim thickness Part number Thickness (mm (in.)) Mark
90564-44074 1.71 (0.0673) E
90564-44075 1.74 (0.0685) F
90564-44076 1.77 (0.0697) G
90564-44077 1.80 (0.0709) H
90564-44078 1.83 (0.0720) J
90564-44079 1.86 (0.0732) K
90564-44080 1.89 (0.0744) L
90564-44081 1.92 (0.0756) M
90564-44082 1.95 (0.0768) N
90564-44083 1.98 (0.0780) P
90564-44084 2.01 (0.0791) Q
90564-44085 2.04 (0.0803) R
90564-44086 2.07 (0.0815) S
90564-44087 2.10 (0.0827) T
90564-44088 2.13 (0.0839) U
90564-44089 2.16 (0.0850) V
90564-44090 2.19 (0.0862) W
90564-44091 2.22 (0.0874) X
90564-44092 2.25 (0.0886) Y
90564-44093 2.28 (0.0898) -
90564-44094 2.31 (0.0909) -
90564-44095 2.34 (0.0921) -
90564-44096 2.37 (0.0933) -
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Transaxle housing type T oil seal Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Torque Converter and Drive Plate
Drive plate runout Maximum 0.30 mm (0.0118 in.)

Front Differential Oil Seal
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Revolution Sensor (NT Sensor)
Transmission revolution sensor (NT)
Tester Connection Condition Specified Condition
D64-1(NTO) - D64-2(NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Revolution Sensor (NOUT Sensor)
Transmission revolution sensor (NOUT)
Tester Connection Condition Specified Condition
D62-1(NOO) - D62-2(NOB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Revolution Sensor (NSS Sensor)
Transmission revolution sensor (NSS)
Tester Connection Condition Specified Condition
D63-1(NSSO) - D63-2(NSSB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Shift Stroke Sensor
Shift stroke sensor
Standard voltage (Combined dry-cell battery voltage of 4.5 V)
Tester Connection Condition Specified Condition
D69-4 (VOUT) - D69-3 (GND) High signal 4.09 to 4.19 V
Low signal 0.36 to 0.45 V
Reference voltage (Combined dry-cell battery voltage of 5.0 V)
Tester Connection Condition Specified Condition
D69-4 (VOUT) - D69-3 (GND) High signal 4.55 to 4.65 V
Low signal 0.4 to 0.5 V

Park/Neutral Position Switch
Park/neutral position switch assembly
Tester Connection Condition Specified Condition
D45-4 (B) - D45-5 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
D45-2 (RB) - D45-6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
D45-2 (RB) - D45-1 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
D45-2 (RB) - D45-9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
D45-2 (RB) - D45-7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
Shift lever not in D, M, "+" or "-" 10 kΩ or higher
D45-2 (RB) - D45-3 (2L) Shift lever in B Below 1 Ω
Shift lever not in B 10 kΩ or higher

Shift Lever
Shift lock control ECU (w/ Smart Entry and Start System)
Wire harness:
Tester Connection Condition Specified Condition
H20-5(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H20-4(STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
H20-1(E) - Body ground Always Below 1 Ω
Shift lock solenoid:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω
Shift lock control ECU (w/o Smart Entry and Start System)
Wire harness:
Tester Connection Condition Specified Condition
H19-1(ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H19-8(STP) - Body ground Ignition switch ON, brake pedal depressed 11 to 14 V
Ignition switch ON, brake pedal released Below 1 V
H19-4(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H19-7(E) - Body ground Always Below 1 Ω
H19-5(KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
Shift lock solenoid:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω
Transmission control switch
Tester Connection Condition Specified Condition
H64-4(IG) - H64-5(S) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
H64-1(SFTU) - H64-2(E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
H64-3(SFTD) - H64-2(E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher

Shift Paddle Switch
No. 1 transmission shift switch assembly
Tester Connection Condition Specified Condition
A-1(SDN) - A-2(ECC) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
A-1(SDN) - A-3(ECC1) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
No. 2 transmission shift switch assembly
Tester Connection Condition Specified Condition
A-1(SUP) - 2(ECC) "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher

Combination Switch
Combination switch assembly
Tester Connection Condition Specified Condition
H18-8(MSW1) - H18-5(E) Switch pushed Below 1 Ω
Switch not pushed 10 kΩ or higher
Measurement Condition Specified Condition
Battery positive (+) → 4 (ILL+) Illuminates
Battery negative (-) → 1 (ILL-)

Valve Body Assembly
Shift solenoid valve (SLG, SL1, SL2, SLU, SLP, SLS)
Tester Connection Condition Specified Condition
B-1 - B-2 20°C (68°F) 5.0 to 5.6 Ω