When the ignition switch to ON, power is supplied to the parking brake ECU (brake actuator assembly). This DTC is stored if IG power source voltage is not supplied to the parking brake ECU (brake actuator assembly) when communication with other ECUs is established.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C102014 | Ignition Switch On/Start Position Circuit Short to Ground or Open | ·
Diagnosis Condition: Ignition switch ON ·
Malfunction Status: When the hybrid vehicle control ECU is communicating via CAN communication, IG power is not input to the parking brake ECU (brake actuator assembly). ·
Detection Time: Approximately 15 seconds |
·
Wire harness and connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | Electric Parking Brake | A | An electric parking brake system malfunction is displayed on the multi-information display. |
Inspect the fuses for circuits related to this system before performing the following procedure.
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the parking brake ECU (brake actuator assembly), perform "Calibration".
When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IGR Voltage | IG voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage |
| Tester Display |
|---|
| IGR Voltage |
| Result | Proceed to |
|---|---|
| The value of IGR Voltage is between 11 and 14 V | A |
| None of the above conditions are met | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C102014 is output | A |
| C102014 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A95 parking brake ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure3
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A95)Location & Routingewd_type=routing;type=c;code=A95 Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A95;pinno=26 |
||
| A95-26 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the A95 parking brake ECU (brake actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A95)Location & Routingewd_type=routing;type=c;code=A95 Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A95;pinno=2 |
||
| A95-2 (EGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG