Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3700E _58 Vehicle Interior _093025 LIGHTING (INT) _0444514 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Push Start Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the push start switch illumination.

WIRING DIAGRAM

for HV Model



E389036E12
3.333,0.708 3.948,0.906 0.615,0.198 10 false SWIL 3.365,1.313 3.979,1.51 0.615,0.198 10 false GND 4.823,0.698 5.135,0.896 0.313,0.198 10 false 20 4.813,1.313 5.125,1.51 0.313,0.198 10 false 30 3.74,0.688 3.896,0.885 0.156,0.198 10 false 5 3.74,1.313 3.896,1.51 0.156,0.198 10 false 3 5.083,0.698 5.698,0.896 0.615,0.198 10 false SWIL 5.073,1.313 5.688,1.51 0.615,0.198 10 false AGND 5.906,0.677 6.219,0.875 0.313,0.198 10 false +B 0.74,2.042 2.698,2.271 1.958,0.229 10 false H69 0.729,2.208 3.479,2.406 2.75,0.198 10 false Power Switch 5.052,2.052 5.51,2.25 0.458,0.198 10 false H46 5.021,2.219 7.146,2.594 2.125,0.375 10 false Certification ECU (Smart Key ECU Assembly)

for Gasoline Model



E389036E13
3.333,0.708 3.948,0.906 0.615,0.198 10 false SWIL 3.365,1.313 3.979,1.51 0.615,0.198 10 false GND 4.823,0.698 5.135,0.896 0.313,0.198 10 false 20 4.813,1.313 5.125,1.51 0.313,0.198 10 false 30 3.74,0.688 3.896,0.885 0.156,0.198 10 false 5 3.74,1.313 3.896,1.51 0.156,0.198 10 false 3 5.083,0.698 5.698,0.896 0.615,0.198 10 false SWIL 5.073,1.313 5.688,1.51 0.615,0.198 10 false AGND 5.906,0.677 6.219,0.875 0.313,0.198 10 false +B 0.74,2.042 2.698,2.271 1.958,0.229 10 false H68 0.74,2.208 3.49,2.406 2.75,0.198 10 false Engine Switch 5.052,2.052 5.51,2.25 0.458,0.198 10 false H46 5.021,2.219 7.146,2.625 2.125,0.406 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.*1

*1: w/ Entry and Start System



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Start SW Light Power Supply Push start switch illumination OFF or ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Start SW Light Power Supply
50004 440 1
OK:

Push start switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PUSH START SWITCH
2.INSPECT PUSH START SWITCH

OK

3.CONFIRM MODEL

NG

3.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

4.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

5.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H69 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H69,H46)Location & Routing

Click Connector(H69)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Switch

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H69-5 (SWIL) - H46-20 (SWIL) Always Below 1 Ω
H69-3 (GND) - H46-30 (AGND) Always Below 1 Ω
H69-5 (SWIL) or H46-20 (SWIL) - Body ground Always 10 kΩ or higher
H69-3 (GND) or H46-30 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H68 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H68,H46)Location & Routing

Click Connector(H68)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Switch

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H68-5 (SWIL) - H46-20 (SWIL) Always Below 1 Ω
H68-3 (GND) - H46-30 (AGND) Always Below 1 Ω
H68-5 (SWIL) or H46-20 (SWIL) - Body ground Always 10 kΩ or higher
H68-3 (GND) or H46-30 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR