Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.07
RM3700E _58 Vehicle Interior _093087 METER / GAUGE / DISPLAY _0438738 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E417683E03
0.771,1 2.333,1.26 1.563,0.26 10 false from IGR-NO. 1 Relay*2 0.927,1.552 2.365,1.802 1.438,0.25 10 false from Auxiliary Battery 3.667,1.708 5,2.031 1.333,0.323 10 false ECU-DCC NO. 2 3.698,1.167 4.781,1.479 1.083,0.313 10 false METER-IGR*2 4.969,3.354 6.792,3.573 1.823,0.219 10 false Combination Meter Assembly 5.24,0.917 5.448,1.083 0.208,0.167 10 false 38 5.51,1 5.792,1.177 0.281,0.177 10 false IG+ 5.24,1.469 5.448,1.635 0.208,0.167 10 false 22 5.24,2.031 5.448,2.198 0.208,0.167 10 false 19 5.25,2.583 5.458,2.75 0.208,0.167 10 false 23 5.51,1.563 5.677,1.74 0.167,0.177 10 false B 5.5,2.688 5.75,2.885 0.25,0.198 10 false ES 5.5,2.125 5.75,2.323 0.25,0.198 10 false EP 4.979,3.188 5.313,3.365 0.333,0.177 10 false H6 0.125,0.438 2.333,0.885 2.208,0.448 10 false from Engine Stop and Start ECU*1 0.167,3.083 2.5,3.417 2.333,0.333 10 false *1: w/ Stop and Start System 0.167,3.417 2.5,3.75 2.333,0.333 10 false *2: w/o Stop and Start System 4.729,0.333 5.042,0.531 0.313,0.198 10 false *1 4.74,0.896 5.052,1.094 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the fuses of circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H6)Location & Routing

Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

H6-19 (EP) - Body ground Always Below 1 Ω
H6-23 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H6)Location & Routing

Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

H6-38 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
H6-22 (B) - Body ground Ignition switch off 11 to 14 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR