Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480837 BRAKE FLUID(for HV Model TMMF Made) N

BRAKE SYSTEM (OTHER)  BRAKE FLUID(for HV Model TMMF Made)  BLEEDING  


CAUTION / NOTICE / HINT

NOTICE:
·

Move the shift lever to P and apply the parking brake before bleeding the brakes.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not operate the brake actuator assembly while air is in the brake system or in the brake master cylinder sub-assembly. Doing so may cause air to enter the brake actuator assembly.

·

If bleeding the brake actuator assembly is difficult due to air in the brake actuator assembly, replace it with a new one.



PROCEDURE

Hide 1.BLEED BRAKE LINE (for LHD)

NOTICE:

Be sure to perform the procedures with the ignition switch off.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL


b.

Remove the center cowl top ventilator louver.

i.
C460899

Disengage the 2 clips and hook to separate the hood to cowl top seal.


ii.
C460900

Disengage the 2 claws and 5 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



c.

Remove the brake master cylinder reservoir filler cap assembly.


d.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




e.

Remove the bleeder plug cap.


f.

Connect a vinyl tube to the bleeder plug.


g.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


h.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


i.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


j.

Tighten the bleeder plug completely.

Torque:

Front Disc Brake Bleeder Plug: 7.5 N*m (76 kgf*cm, 66 in.*lbf)

Rear Disc Brake Bleeder Plug (for 2WD): 6.5 N*m (66 kgf*cm, 58 in.*lbf)

Rear Disc Brake Bleeder Plug (for AWD): 8.3 N*m (85 kgf*cm, 73 in.*lbf)



k.

Install the bleeder plug cap.


l.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


m.

Inspect for brake fluid leaks.


n.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model TMMF Made)>ON-VEHICLE INSPECTION


o.

Install the brake master cylinder reservoir filler cap assembly.


p.

Install the center cowl top ventilator louver.

i.

Engage the 5 guides and 2 claws to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.


ii.

Engage the 2 clips and hook to install the hood to cowl top seal.



q.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION


Hide 2.BLEED BRAKE LINE (for RHD)

NOTICE:

Be sure to perform the procedures with the ignition switch off.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL


b.

Remove the center cowl top ventilator louver.

i.
C460902

Disengage the 2 clips and hook to separate the hood to cowl top seal.


ii.
C460903

Disengage the 2 claws and 5 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



c.

Remove the brake master cylinder reservoir filler cap assembly.


d.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




e.

Remove the bleeder plug cap.


f.

Connect a vinyl tube to the bleeder plug.


g.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


h.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


i.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


j.

Tighten the bleeder plug completely.

Torque:

Front Disc Brake Bleeder Plug: 7.5 N*m (76 kgf*cm, 66 in.*lbf)

Rear Disc Brake Bleeder Plug (for 2WD): 6.5 N*m (66 kgf*cm, 58 in.*lbf)

Rear Disc Brake Bleeder Plug (for AWD): 8.3 N*m (85 kgf*cm, 73 in.*lbf)



k.

Install the bleeder plug cap.


l.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


m.

Inspect for brake fluid leaks.


n.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model TMMF Made)>ON-VEHICLE INSPECTION


o.

Install the brake master cylinder reservoir filler cap assembly.


p.

Install the center cowl top ventilator louver.

i.

Engage the 5 guides and 2 claws to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.


ii.

Engage the 2 clips and hook to install the hood to cowl top seal.



q.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION