Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR (for TMC Made) › from 2021.07
RM3700E _59 Vehicle Exterior _092997 MIRROR (EXT) _0482017 OUTER REAR VIEW MIRROR(for TMC Made) G

MIRROR (EXT)  OUTER REAR VIEW MIRROR(for TMC Made)  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Panoramic View Monitor System)

a.

w/o Mirror Heater:

i.
B586261C02
1.563,1.76 1.958,1.958 0.396,0.198 1.573,3.219 1.917,2.844 true 2.146,2.844 2.438,3.104 true 1.76,0.104 2,0.281 0.24,0.177 10 false (A) 2.26,0.646 2.573,0.802 0.313,0.156 10 false (B) 2.26,1.135 2.573,1.292 0.313,0.156 10 false (C) 1.917,1.448 2.229,1.604 0.313,0.156 10 false (D) 1.365,1.531 1.604,1.698 0.24,0.167 10 false (E) 0.896,1.875 1.094,2.052 0.198,0.177 10 false *a 2.479,3.063 2.792,3.219 0.313,0.156 10 false MR 1.469,3.229 1.781,3.385 0.313,0.156 10 false MF 1.646,1.781 2.052,1.938 0.406,0.156 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



1. Disconnect the outer rear view mirror assembly RH connector.

2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K10)Location & Routing

Click Connector(K10)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.


ii.
B586262C03
1.563,1.667 1.969,1.885 0.406,0.219 2,2.406 2.563,2 true 2.24,2.469 2.594,2.396 true 2.344,2.792 2.563,2.927 true 0.885,1.875 1.198,2.031 0.313,0.156 10 false *a 2.615,1.927 2.927,2.083 0.313,0.156 10 false MV 2.635,2.323 2.948,2.479 0.313,0.156 10 false M+ 2.594,2.875 2.906,3.031 0.313,0.156 10 false MH 1.646,1.698 1.958,1.854 0.313,0.156 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror surface.

1. Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Tester Connection Specified Condition

Click Location & Routing(K10)Location & Routing

Click Connector(K10)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K10-1 (MV) - Auxiliary battery positive (+)
K10-2 (M+) - Auxiliary battery negative (-)
Turns upward
K10-2 (M+) - Auxiliary battery positive (+)
K10-1 (MV) - Auxiliary battery negative (-)
Turns downward
K10-3 (MH) - Auxiliary battery positive (+)
K10-2 (M+) - Auxiliary battery negative (-)
Turns left
K10-2 (M+) - Auxiliary battery positive (+)
K10-3 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.
B585922C02
1.51,0.323 1.927,0.573 0.417,0.25 1.708,1.875 1.458,1.5 true 0.885,1.865 1.188,1.458 true 0.604,0.677 0.917,0.833 0.313,0.156 10 false *a 0.813,1.906 1.125,2.063 0.313,0.156 10 false B 1.729,1.896 2.042,2.052 0.313,0.156 10 false - 1.594,0.375 1.917,0.625 0.323,0.25 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the side turn signal light assembly RH.

1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(K10)Location & Routing

Click Connector(K10)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K10-4 (B) - Auxiliary battery positive (+)
K10-5 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.



b.

w/ Mirror Heater:

i.
B586291C02
1.563,1.76 1.958,1.958 0.396,0.198 0.635,2.479 1.479,2.667 true 1.531,3.01 0.76,3.219 true 2.021,0 2.26,0.177 0.24,0.177 10 false (A) 2.292,0.583 2.604,0.74 0.313,0.156 10 false (B) 2.292,1.146 2.604,1.302 0.313,0.156 10 false (C) 1.917,1.448 2.229,1.604 0.313,0.156 10 false (D) 1.365,1.531 1.604,1.698 0.24,0.167 10 false (E) 0.563,1.896 0.76,2.073 0.198,0.177 10 false *a 0.417,2.406 0.729,2.563 0.313,0.156 10 false MR 0.552,3.198 0.865,3.354 0.313,0.156 10 false MF 1.646,1.802 2.052,1.958 0.406,0.156 10 false K13
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



1. Disconnect the outer rear view mirror assembly RH connector.

2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K13)Location & Routing

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K13-3 (MR) - Auxiliary battery positive (+)
K13-9 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
K13-9 (MF) - Auxiliary battery positive (+)
K13-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
K13-3 (MR) - Auxiliary battery positive (+)
K13-9 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
K13-9 (MF) - Auxiliary battery positive (+)
K13-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
K13-3 (MR) - Auxiliary battery positive (+)
K13-9 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
K13-9 (MF) - Auxiliary battery positive (+)
K13-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
K13-3 (MR) - Auxiliary battery positive (+)
K13-9 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
K13-9 (MF) - Auxiliary battery positive (+)
K13-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
K13-3 (MR) - Auxiliary battery positive (+)
K13-9 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
K13-9 (MF) - Auxiliary battery positive (+)
K13-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.


ii.
B586292C01
1.563,1.667 1.969,1.885 0.406,0.219 1.896,2.625 2.5,1.844 true 2.146,2.656 2.792,2.135 true 2.427,2.802 2.771,3.073 true 0.542,1.854 0.854,2.01 0.313,0.156 10 false *a 2.813,3.01 3.125,3.167 0.313,0.156 10 false MV 2.833,2.042 3.146,2.198 0.313,0.156 10 false M+ 2.552,1.76 2.865,1.917 0.313,0.156 10 false MH 1.646,1.698 1.958,1.854 0.313,0.156 10 false K13
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror surface.

1. Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Tester Connection Specified Condition

Click Location & Routing(K13)Location & Routing

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K13-6 (MV) - Auxiliary battery positive (+)
K13-5 (M+) - Auxiliary battery negative (-)
Turns upward
K13-5 (M+) - Auxiliary battery positive (+)
K13-6 (MV) - Auxiliary battery negative (-)
Turns downward
K13-4 (MH) - Auxiliary battery positive (+)
K13-5 (M+) - Auxiliary battery negative (-)
Turns left
K13-5 (M+) - Auxiliary battery positive (+)
K13-4 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.
B586293C01
1.563,1.667 1.969,1.885 0.406,0.219 1.271,2.688 0.531,2.375 true 2.521,3.281 2.156,3.031 true 0.615,1.865 0.927,2.021 0.313,0.156 10 false *a 0.396,2.281 0.708,2.438 0.313,0.156 10 false + 1.646,1.698 1.958,1.854 0.313,0.156 10 false K13 2.563,3.24 2.875,3.396 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror heater.

1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K13)Location & Routing

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K13-2 (+) - K13-11 (-) 25°C 10 to 17 Ω


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.

2. Connect a cable from the positive (+) auxiliary battery terminal to K13-2 (+) and negative (-) auxiliary battery terminal to K13-11 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.


iv.
B585923C09
1.51,0.229 1.927,0.479 0.417,0.25 2.188,1.969 1.927,1.583 true 2.573,1.885 2.146,1.594 true 0.49,0.49 0.802,0.646 0.313,0.156 10 false *a 2.25,1.917 2.563,2.073 0.313,0.156 10 false B 2.635,1.833 2.948,1.99 0.313,0.156 10 false - 1.604,0.302 1.927,0.552 0.323,0.25 10 false K13
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the side turn signal light assembly RH.

1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(K13)Location & Routing

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K13-10 (B) - Auxiliary battery positive (+)
K13-11 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.


v.
B585923C10
1.51,0.229 1.927,0.479 0.417,0.25 2.49,1.938 2.188,1.573 true 0.646,1.271 1.073,1.313 true 0.49,0.49 0.802,0.646 0.313,0.156 10 false *a 2.552,1.896 2.865,2.052 0.313,0.156 10 false - 0.281,1.198 0.75,1.406 0.469,0.208 10 false BSR+ 1.604,0.302 1.927,0.552 0.323,0.25 10 false K13
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the blind spot monitor indicator.

1. Connect 4 new 1.5 V dry-cell batteries in series.

NOTICE:

Do not apply a voltage of 6 V or higher.


2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(K13)Location & Routing

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K13-1 (BSR+) - Positive (+) end of the 6 V dry-cell battery
K13-11 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Panoramic View Monitor System)

a.

w/o Mirror Heater:

i.
B586263C02
1.583,1.792 2,2 0.417,0.208 1.656,3.229 1.927,2.854 true 2.146,2.844 2.417,3.094 true 1.49,0.115 1.802,0.271 0.313,0.156 10 false (A) 0.969,0.615 1.229,0.781 0.26,0.167 10 false (B) 0.917,1.146 1.115,1.313 0.198,0.167 10 false (C) 1.302,1.438 1.5,1.594 0.198,0.156 10 false (D) 1.885,1.531 2.198,1.688 0.313,0.156 10 false (E) 0.938,1.906 1.25,2.063 0.313,0.156 10 false *a 1.542,3.25 1.885,3.417 0.344,0.167 10 false MF 2.458,3.052 2.771,3.208 0.313,0.156 10 false MR 1.667,1.813 2.01,1.979 0.344,0.167 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



1. Disconnect the outer rear view mirror assembly LH connector.

2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(L10)Location & Routing

Click Connector(L10)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.


ii.
B586264C01
1.583,1.729 2.01,1.958 0.427,0.229 2.229,2.406 2.646,2.229 true 2.323,2.802 2.542,2.99 true 1.969,2.417 2.635,1.896 true 0.906,1.875 1.104,2.031 0.198,0.156 10 false *a 2.688,2.146 2.896,2.323 0.208,0.177 10 false M+ 2.573,2.938 2.833,3.104 0.26,0.167 10 false MH 2.677,1.823 2.917,1.99 0.24,0.167 10 false MV 1.688,1.771 2.146,1.969 0.458,0.198 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror surface.

1. Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Tester Connection Specified Condition

Click Location & Routing(L10)Location & Routing

Click Connector(L10)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L10-1 (MV) - Auxiliary battery positive (+)
L10-2 (M+) - Auxiliary battery negative (-)
Turns upward
L10-2 (M+) - Auxiliary battery positive (+)
L10-1 (MV) - Auxiliary battery negative (-)
Turns downward
L10-3 (MH) - Auxiliary battery positive (+)
L10-2 (M+) - Auxiliary battery negative (-)
Turns left
L10-2 (M+) - Auxiliary battery positive (+)
L10-3 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.
B585922C01
1.51,0.323 1.927,0.573 0.417,0.25 1.74,1.854 1.479,1.469 true 0.875,1.875 1.177,1.469 true 0.563,0.677 0.875,0.833 0.313,0.156 10 false *a 0.771,1.875 1.083,2.031 0.313,0.156 10 false B 1.781,1.875 2.094,2.031 0.313,0.156 10 false - 1.594,0.375 1.917,0.625 0.323,0.25 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the side turn signal light assembly LH.

1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(L10)Location & Routing

Click Connector(L10)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L10-4 (B) - Auxiliary battery positive (+)
L10-5 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.



b.

w/ Mirror Heater:

i.
B586288C02
1.583,1.792 2,2 0.417,0.208 0.76,3.271 1.458,3 true 1.51,2.656 0.573,2.385 true 1.188,0.01 1.5,0.167 0.313,0.156 10 false (A) 0.958,0.583 1.219,0.75 0.26,0.167 10 false (B) 0.948,1.135 1.146,1.302 0.198,0.167 10 false (C) 1.281,1.438 1.479,1.594 0.198,0.156 10 false (D) 1.865,1.531 2.177,1.688 0.313,0.156 10 false (E) 0.417,1.906 0.729,2.063 0.313,0.156 10 false *a 0.521,3.219 0.865,3.385 0.344,0.167 10 false MF 0.333,2.313 0.646,2.469 0.313,0.156 10 false MR 1.667,1.813 2.01,1.979 0.344,0.167 10 false L12
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



1. Disconnect the outer rear view mirror assembly LH connector.

2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-3 (MR) - Auxiliary battery positive (+)
L12-9 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
L12-9 (MF) - Auxiliary battery positive (+)
L12-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
L12-3 (MR) - Auxiliary battery positive (+)
L12-9 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
L12-9 (MF) - Auxiliary battery positive (+)
L12-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
L12-3 (MR) - Auxiliary battery positive (+)
L12-9 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
L12-9 (MF) - Auxiliary battery positive (+)
L12-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
L12-3 (MR) - Auxiliary battery positive (+)
L12-9 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
L12-9 (MF) - Auxiliary battery positive (+)
L12-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
L12-3 (MR) - Auxiliary battery positive (+)
L12-9 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
L12-9 (MF) - Auxiliary battery positive (+)
L12-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.


ii.
B586289C01
1.583,1.729 2.01,1.958 0.427,0.229 2.156,2.656 2.885,2.479 true 2.406,2.792 2.792,3.052 true 1.896,2.656 2.469,1.854 true 0.458,1.875 0.656,2.031 0.198,0.156 10 false *a 2.927,2.396 3.135,2.573 0.208,0.177 10 false M+ 2.51,1.771 2.771,1.938 0.26,0.167 10 false MH 2.854,3.031 3.094,3.198 0.24,0.167 10 false MV 1.688,1.771 2.146,1.969 0.458,0.198 10 false L12
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror surface.

1. Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Tester Connection Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-6 (MV) - Auxiliary battery positive (+)
L12-5 (M+) - Auxiliary battery negative (-)
Turns upward
L12-5 (M+) - Auxiliary battery positive (+)
L12-6 (MV) - Auxiliary battery negative (-)
Turns downward
L12-4 (MH) - Auxiliary battery positive (+)
L12-5 (M+) - Auxiliary battery negative (-)
Turns left
L12-5 (M+) - Auxiliary battery positive (+)
L12-4 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.
B586290C01
1.583,1.729 2.01,1.958 0.427,0.229 2.146,3.042 2.531,3.302 true 1.292,2.667 0.583,2.438 true 0.458,1.875 0.656,2.031 0.198,0.156 10 false *a 0.469,2.385 0.677,2.563 0.208,0.177 10 false + 2.583,3.24 2.792,3.385 0.208,0.146 10 false - 1.688,1.771 2.146,1.969 0.458,0.198 10 false L12
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror heater.

1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-2 (+) - L12-11 (-) 25°C 10 to 17 Ω


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.

2. Connect a cable from the positive (+) auxiliary battery terminal to L12-2 (+) and negative (-) auxiliary battery terminal to L12-11 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.


iv.
B585923C11
1.51,0.323 1.927,0.573 0.417,0.25 2.427,1.958 2.167,1.573 true 1.625,2 1.927,1.594 true 0.563,0.677 0.875,0.833 0.313,0.156 10 false *a 1.521,1.958 1.833,2.115 0.313,0.156 10 false B 2.479,1.927 2.792,2.083 0.313,0.156 10 false - 1.625,0.375 1.948,0.625 0.323,0.25 10 false L12
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the side turn signal light assembly LH.

1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-10 (B) - Auxiliary battery positive (+)
L12-11 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.


v.
B585923C12
1.51,0.229 1.927,0.479 0.417,0.25 2.49,1.938 2.188,1.573 true 0.646,1.271 1.073,1.313 true 0.49,0.49 0.802,0.646 0.313,0.156 10 false *a 2.552,1.896 2.865,2.052 0.313,0.156 10 false - 0.281,1.198 0.75,1.406 0.469,0.208 10 false BSL+ 1.604,0.302 1.927,0.552 0.323,0.25 10 false L12
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the blind spot monitor indicator.

1. Connect 4 new 1.5 V dry-cell batteries in series.

NOTICE:

Do not apply a voltage of 6 V or higher.


2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-1 (BSL+) - Positive (+) end of the 6 V dry-cell battery
L12-11 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Panoramic View Monitor System)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B586265C02
1.5,1.781 1.906,2.01 0.406,0.229 1.385,2.646 0.625,2.271 true 1.427,2.99 0.656,3.24 true 2.01,0.01 2.323,0.208 0.313,0.198 10 false (A) 2.229,0.49 2.542,0.688 0.313,0.198 10 false (B) 2.281,1.125 2.594,1.323 0.313,0.198 10 false (C) 1.958,1.417 2.271,1.615 0.313,0.198 10 false (D) 1.344,1.542 1.656,1.74 0.313,0.198 10 false (E) 0.583,1.958 0.896,2.156 0.313,0.198 10 false *a 0.438,3.177 0.75,3.375 0.313,0.198 10 false MF 0.375,2.177 0.688,2.375 0.313,0.198 10 false MR 1.615,1.823 1.927,2.021 0.313,0.198 10 false K8
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



b.

Check the operation of the mirror surface.

i.
B586266C01
1.51,1.76 1.896,1.979 0.385,0.219 0.573,2.302 1.042,2.688 true 0.542,2.646 1.042,2.927 true 0.646,3.24 1.281,2.969 true 0.542,1.917 0.854,2.115 0.313,0.198 10 false *a 1.615,1.792 1.927,1.99 0.313,0.198 10 false K8 0.354,2.219 0.708,2.448 0.354,0.229 10 false MV 0.292,2.552 0.646,2.781 0.354,0.229 10 false MH 0.396,3.198 0.75,3.427 0.354,0.229 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Tester Connection Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K8-1 (MV) - Auxiliary battery positive (+)
K8-10 (M+) - Auxiliary battery negative (-)
Turns upward
K8-10 (M+) - Auxiliary battery positive (+)
K8-1 (MV) - Auxiliary battery negative (-)
Turns downward
K8-9 (MH) - Auxiliary battery positive (+)
K8-10 (M+) - Auxiliary battery negative (-)
Turns left
K8-10 (M+) - Auxiliary battery positive (+)
K8-9 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the mirror heater.

i.
B586267C01
1.531,1.74 1.917,1.99 0.385,0.25 2.177,2.677 2.75,2.177 true 2.188,2.969 2.823,3.146 true 0.531,1.948 0.844,2.146 0.313,0.198 10 false *a 1.635,1.771 1.948,1.969 0.313,0.198 10 false K8 2.802,2.052 3.115,2.25 0.313,0.198 10 false + 2.906,3.083 3.219,3.281 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K8-7 (+) - K8-15 (-) 25°C 10 to 17 Ω


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to K8-7 (+) and negative (-) auxiliary battery terminal to K8-15 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.



d.

Check the side turn signal light assembly RH.

i.
B585924C03
1.5,0.24 1.917,0.49 0.417,0.25 2.052,1.906 2.167,1.563 true 2.906,1.729 2.396,1.521 true 0.385,0.438 0.698,0.594 0.313,0.156 10 false *a 2.01,1.896 2.417,2.146 0.406,0.25 10 false - 2.979,1.688 3.365,1.885 0.385,0.198 10 false B 1.604,0.281 2.01,0.531 0.406,0.25 10 false K8
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K8-16 (B) - Auxiliary battery positive (+)
K8-15 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.



e.

Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor System)

i.
B585924C04
1.5,0.208 1.917,0.458 0.417,0.25 2.948,1.24 2.417,1.271 true 2.177,1.563 2.604,1.938 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 2.99,1.167 3.427,1.365 0.438,0.198 10 false BSR+ 2.635,1.938 3.073,2.135 0.438,0.198 10 false - 1.594,0.25 1.938,0.479 0.344,0.229 10 false K8
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Connect 4 new 1.5 V dry-cell batteries in series.

NOTICE:

Do not apply a voltage of 6 V or higher.


2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

K8-8 (BSR+) - Positive (+) end of the 6 V dry-cell battery
K8-15 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.



Hide 87940 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Panoramic View Monitor System)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B586268C02
1.521,1.771 1.906,2.01 0.385,0.24 0.688,3.208 1.438,2.979 true 0.688,2.313 1.396,2.667 true 1.198,0.042 1.51,0.24 0.313,0.198 10 false (A) 1,0.49 1.313,0.688 0.313,0.198 10 false (B) 0.958,1.125 1.271,1.323 0.313,0.198 10 false (C) 1.292,1.427 1.604,1.625 0.313,0.198 10 false (D) 1.844,1.531 2.156,1.729 0.313,0.198 10 false (E) 1.635,1.813 1.948,2.01 0.313,0.198 10 false L8 0.625,1.969 0.938,2.167 0.313,0.198 10 false *a 0.469,2.219 0.781,2.417 0.313,0.198 10 false MR 0.458,3.146 0.771,3.344 0.313,0.198 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



b.

Check the operation of the mirror surface.

i.
B586269C01
1.552,1.771 1.885,1.99 0.333,0.219 0.635,2.281 1.031,2.656 true 0.646,2.688 1.042,2.927 true 0.854,3.281 1.24,2.969 true 1.635,1.802 1.948,2 0.313,0.198 10 false L8 0.521,1.917 0.833,2.115 0.313,0.198 10 false *a 0.385,2.219 0.698,2.417 0.313,0.198 10 false MV 0.417,2.615 0.729,2.813 0.313,0.198 10 false MH 0.615,3.229 0.927,3.427 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Tester Connection Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-1 (MV) - Auxiliary battery positive (+)
L8-10 (M+) - Auxiliary battery negative (-)
Turns upward
L8-10 (M+) - Auxiliary battery positive (+)
L8-1 (MV) - Auxiliary battery negative (-)
Turns downward
L8-9 (MH) - Auxiliary battery positive (+)
L8-10 (M+) - Auxiliary battery negative (-)
Turns left
L8-10 (M+) - Auxiliary battery positive (+)
L8-9 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the mirror heater.

i.
B586270C01
1.521,1.771 1.917,1.99 0.396,0.219 2.188,2.656 2.792,2.177 true 2.198,2.917 2.844,2.573 true 0.594,1.948 0.906,2.146 0.313,0.198 10 false *a 1.635,1.802 1.948,2 0.313,0.198 10 false L8 2.865,2.083 3.177,2.281 0.313,0.198 10 false + 2.896,2.469 3.208,2.667 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-7 (+) - L8-15 (-) 25°C 10 to 17 Ω


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to L8-7 (+) and negative (-) auxiliary battery terminal to L8-15 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.



d.

Check the side turn signal light assembly LH.

i.
B585924C01
1.5,0.24 1.917,0.49 0.417,0.25 2.063,1.906 2.177,1.563 true 2.896,1.688 2.406,1.531 true 0.385,0.438 0.698,0.594 0.313,0.156 10 false *a 2.031,1.896 2.438,2.146 0.406,0.25 10 false - 2.958,1.625 3.344,1.823 0.385,0.198 10 false B 1.604,0.281 2.01,0.531 0.406,0.25 10 false L8
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-16 (B) - Auxiliary battery positive (+)
L8-15 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.



e.

Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor System)

i.
B585924C02
1.5,0.208 1.917,0.458 0.417,0.25 2.875,1.198 2.417,1.271 true 2.167,1.573 2.615,1.958 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 2.917,1.125 3.354,1.323 0.438,0.198 10 false BSL+ 2.667,1.938 3.104,2.135 0.438,0.198 10 false - 1.594,0.25 1.938,0.479 0.344,0.229 10 false L8
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Connect 4 new 1.5 V dry-cell batteries in series.

NOTICE:

Do not apply a voltage of 6 V or higher.


2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-8 (BSL+) - Positive (+) end of the 6 V dry-cell battery
L8-15 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.