Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS › from 2021.07
RM3700E _59 Vehicle Exterior _092997 MIRROR (EXT) _0438350 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87961 1.INSPECT OUTER MIRROR LH (for TMC Made)

a.

Check the operation of the mirror heater.

i.
B586278C01
0.719,0.5 1.458,0.885 true 0.625,1.24 1.469,1.24 true 0.938,0.167 1.25,0.365 0.313,0.198 10 false *a 0.615,0.417 0.927,0.615 0.313,0.198 10 false 1 0.49,1.156 0.802,1.354 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10 to 17 Ω



ii.

If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B586279C01
0.333,0.74 0.646,0.938 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

NOTICE:

Do not apply a voltage of more than 6 V.


OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror LH.



Hide 87931 2.INSPECT OUTER MIRROR RH (for TMC Made)

a.

Check the operation of the mirror heater.

i.
B586280C01
1.958,0.885 2.656,0.708 true 1.958,1.229 2.917,1.229 true 2.969,1.135 3.125,1.365 0.156,0.229 10 false 2 2.708,0.625 2.865,0.854 0.156,0.229 10 false 1 2.323,0.219 2.604,0.417 0.281,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10 to 17 Ω



ii.

If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B586281C01
2.26,0.688 2.573,0.885 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

NOTICE:

Do not apply a voltage of more than 6 V.


OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror RH.



Hide 87961 3.INSPECT OUTER MIRROR LH (for TMMF Made)

a.

Check the operation of the mirror heater.

i.
B603711C01
0.479,1.073 1.646,1.073 true 0.51,1.625 1.469,1.625 true 0.344,1.552 0.5,1.781 0.156,0.229 10 false 2 0.344,1 0.5,1.229 0.156,0.229 10 false 1 0.167,0.167 0.448,0.365 0.281,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10.5 to 12.8 Ω



ii.

If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B603712C01
0.344,0.552 0.656,0.75 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

NOTICE:

Do not apply a voltage of more than 6 V.


OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror LH.



Hide 87931 4.INSPECT OUTER MIRROR RH (for TMMF Made)

a.

Check the operation of the mirror heater.

i.
B603713C01
1.792,1.073 2.875,1.073 true 1.979,1.615 2.896,1.615 true 2.75,0.25 3.063,0.448 0.313,0.198 10 false *a 2.948,0.969 3.26,1.167 0.313,0.198 10 false 1 2.958,1.51 3.271,1.708 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10.5 to 12.8 Ω



ii.

If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B603714C01
0.333,0.656 0.646,0.854 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

NOTICE:

Do not apply a voltage of more than 6 V.


OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror RH.